Bosch CET3-10 3 Gallon 1 HP Mini Twin Angled Tank Air Compressor

by Bosch

Product Description

Amazon.com Product Description

The Bosch CET3-10 Three-Gallon, One-HP Mini Twin-Angled Tank Air Compressor is portable enough to move from site to site, simple to operate and maintain, and tough enough to withstand heavy-duty conditions. It's also CSA-certified, easy to store, and great for a range of carpentry, framing, roofing, and remodeling jobs.

The CET3-10 Three-Gallon, One-HP Mini Twin-Angled Tank Air Compressor offers: Angled "EZ Drain" system for effortless draining. Four-pole induction motor for powerful performance.

A recessed control panel provides long-term protection from the elements. View larger.

Vertically angled tanks allow for easy draining and balance the compressor for portability.

Vertically Angled Tanks for Your Comfort
Other air compressors can cause discomfort because they lack balance, and their exposed motor and components make them difficult to carry. But the CET3-10 is comfortable to use, because it features vertically angled tanks that are ergonomically balanced. And because this compressor stays close to your body, it provides a natural center of gravity. Additionally, the roll cage and recessed, easy-access control panel protect you from exposure to the regulator, gauges, coupler, and drain valve.

Compact Size for Enhanced Portability
Unlike large wheeled compressors that hold the majority of their weight in front, the CET3-10 is balanced, measuring 17.0 x 16.25 x 16.0 inches (WxHxL) and weighing 57.3 pounds. It's compact, lightweight, and even enough for effortless movement around the jobsite.

EZ Drain System for Fast, Efficient Draining
To ensure that the tanks drain properly, and to prevent a decrease in compression that can cause a decrease in productivity and performance, the CET3-10 boasts Bosch's "EZ Drain" system. First, the tanks are slightly angled to allow water to collect at their bottoms. Second, the drain system is connected to both tanks to allow for easier draining. Finally, with pressure in the tanks, you can simultaneously drain them both by turning the ball valve located in the control panel.

Recessed Control Panel and Roll Cage Protect Components from Damage
Many air compressors have exposed components that are unprotected from harsh jobsite conditions--but not the CET3-10. This compressor has a recessed control panel that fully protects the regulator, gauges, coupler, and drain valve. Additionally, a roll cage shields the pump, motor, tanks, safety-relief valve, and all internal components. The result is less downtime and more productivity.

Safety-Relief Valve, Air Filter, and Dipstick for Additional Protection
In addition to its protective design, the CET3-10 features a safety-relief valve to prevent failures by relieving pressure from the system when compressed air reaches a predetermined level. And to prevent dirt and debris from compromising performance or durability, an air filter cleans the air coming into the pump. Additionally, an oil dipstick lets you know exactly how much oil is left in the tank, so it's always clear when it's time to refuel.

Powerful and Quiet Induction Motor
The CET3-10 owes its robust performance to a four-pole induction motor, which provides a dBa of 72 for quiet operation, keeping you free of distraction when you're working close to the compressor.

Additionally, a contractor-grade, oil-lubed pump ensures durability and extends tool life. The CET3-10 comes with an industry-leading, two-year pump warranty.

Straightforward, User-Friendly Operation
The CET3-10 has an easy-to-read tank pressure gauge that lets you know the amount of pressure available, as well as a regulator that allows you to easily set the right level for driving nails. Additionally, two couplers are located on the tool's front for fast, uncomplicated hose attachment. For added convenience, the CET3-10 requires just 14 seconds of recovery time.

What's in the Box
Compressor with oil in the pump.

For more information, click on the images below
Bosch Nail Guns and Compressors
SN350-20F Full Head Framing Nailer	SN350-34C Clipped Head Framing Nailer	FNA250-15 15 Gauge Angled Finish Nailer	FNS250-16 16 Gauge Angled Finish Nailer	BNS200-18 18 Gauge Brad Nailer	STN150-18 18 Gauge Narrow Crown Stapler
RN175 Coil Roofing Nailer	CGT8-65W 8 Gallon 6.5 HP Gas Wheelbarrow Air Compressor	CET8-15W 8 Gallon 1.5 HP Electric Wheelbarrow Air Compressor	CET3-10 3 Gallon Electric Hand Carry Compressor	CET4-20 4 Gallon Electric Hand Carry Compressor	CET4-20W 4 Gallon Electric Compressor w/ Wheels

Product Description

Includes 3-Gallon Angled Tank 1 HP Mini Twin Compressor - CET3-10-RT

See all Product Description

Product Details

• Shipping Weight: 71.4 pounds (View shipping rates and policies)
• Shipping: Currently, item can be shipped only within the U.S. and to APO/FPO addresses. For APO/FPO shipments, please check with the manufacturer regarding warranty and support issues.
• ASIN: B0022NHVU0
• Item model number: CET3-10
• Average Customer Review: 3.0 out of 5 stars  See all reviews (1 customer review)
• Amazon Best Sellers Rank: #230,145 in Home Improvement (See Top 100 in Home Improvement)

Customer Reviews

Most Helpful Customer Reviews

12 of 12 people found the following review helpful:

3.0 out of 5 stars Bosch CET-3 review-mostly good/some not great, August 26, 2010

By 

funkguitar - See all my reviews

This review is from: Bosch CET3-10 3 Gallon 1 HP Mini Twin Angled Tank Air Compressor (Tools & Home Improvement)

I bought this air compressor because mainly: it had a contractor grade pump, said it was well balanced for easy maneuvering around the jobsite, oil-lube pump, 79dB (decibel) 3 gallon twin stack (vertically positioned) for more free air and 2.6 CFM.

The good: this thing works well, and I found out it has 100% duty rating (or continous duty). I can use it all day and runs well and the pump doesn't seem to get too hot. It has a pretty fast pump up/recovery time, and pretty fast initial pump up. Not sure of the initial pump up stat, probally slightly over 1 min, revovery is probally around 16-18 seconds (not quite as fast as Bosch claims, but close. You can still sink nails even when the compressor is recycling, which is a plus, as some compressors won't counter sink nails until it fully recovers. I used it fine with an Omer 12.50 18 ga brad nailer (about 35-40) before it kicked in. It worked well with an Hitachi 15 ga nailer (possibly around the same number of nails, I stop keeping track). I also used a Craftsman utility coil nailer (2-1/4" ring shank) for 5/8" T-1-11 and worked well all day firing off coil after coil. Lastly, I also used a craftsman framing nailer for framing work, however after about 3-5 shots the compressor kicked in, but I pretty much used it all day long and was sinking the nails; very rarely did it leave a framing nail slightly proud. The compressor was recycling often while framing and shooting the coil nails, but it kept on giving me the air to get the job done. Now, I wouldn't hook into the CET-3 as a regular component for framing, and in a rapid fire nail off, but It was out for the finish work, so I used it, and did the job. The coil nailer used much less air per shot than framing and actually kept up decently firing in bump mode all day.

The Bad: this air compressor is awkward to move around. and fairly heavy too. It claims it's center of gravity is better because the tanks are vertically positioned making it to move around the jobsite. You have to reach in the middle for the handle, and rest the side of the compressor on your leg as you walk it. It is a Pain walking this thing up flights of stairs, so if you are looking for something small and light to do finish work, you can find another compressor. I found it actually much easier to grap it with two hands by the top roll bar/frame and rest the bottom plate on my belt buckle, it frees up your leg and you can take a full stride, up stairs or where ever. Decibels/loudness- it claims it is 79dB, well indoors it definately seems louder than that. Now, I obviously didn't have a decibel meter, but I have used the Senco PC1010 plenty times, and that is listed around 76-79dB (give or take a few) and that compressor is ridicuously quite. The Bosch is noticeably louder, and if the Senco is say 76dB no way is the Bosch 79dB. Also, if you are working in and old house with loose floor boards, it vibrates and can increase the noise and the unit can walk on you; so you'll need to put it on a stable, clean surface (not on a drop cloth or dusty floor, rubberized feet need to contact solid substrate). But also, with saying that, this unit is quiter than most and you definately won't go deaf or anything working next to it, and you can carry on a conversation with it running.

Last tip: the manual is very basic, probally written in Chinese and translated to English (to rationalize some of the wording/grammar issues) which makes you read a few parts twice. This unit is made in CHINA too, maybe some of the parts are made domestically (maybe not) but it is definately made in China, I emailed Bosch and they said it was made here in USA-WRONG!. Make sure you break-it-in correctly before putting it to use.

Very Simple:(1) Open drain valve (on bottom of front plate) twist 1/4" turn

(2) plug unit in and turn lever ON

(3) run the compressor for 20 min continuously

(4) after twenty min, close drain valve-letting tanks fill-when it auto turns off at 125 psi- break-in is done

(5) CHANGE OIL!!!!!! (they don't tell you this, but it only benefits your new purchase)

Things to remember-don't be stupid and check the freggin' oil level first before you break it in. And yes, immediately after you break it in, get that oil outta there and get some fresh oil back in, you'll see what i'm saying when you see how dirty it is. Best oil I found to use is: MOBILE RARUS 427 (about $8.50 1 qt) lasts many oil changes. It takes about 150 ml to fill. (how do I measure 150 ml? buy a clear plastic bucket with ml marks on it, fill bucket to line, use a funnel & pour)

Also, try to always run your compressor on a level surface, if the ground, or driveway etc is pitched/sloped you can ruin your compressor because the motor isn't getting lubed properly, the oil will pool to one side and the parts inside won't pick up any oil. level is the way to go.

OK enough ramblin' on- If you are looking for a small professional grade compressor to use on mainly finish work, with an occational coil/ light framing nailer (not a high speed nail off) and the extra weight of the compressor is no issue, it's perfect. BTW, the extra weight is mainly to do from the heavy duty pump and the heavy duty roll bar/frame design, two features most contractors will gladly trade off for the extra weight beacause this thing is built to last. If, on the other hand you do mostly light punch out work,quarter round, shoe, trim out 1 window here & there and want something very easy to pick up & move around without dealing with oil changes, buy another compressor. Quick other points: Bosch's drain valve is the best design, it functions by turning only a 1/4 turn to open or close. Not the threaded kind that sticks out at the bottom, can break off or threads can strip. Pressure/regulator gauges are small and you have to bend down low and get close to read. Tool pressure knob doesn't feel real solid, cheaper light gauge plastic. Rubberized feet are very spongey and solid to absorb vibrations well (if your feet where out, you have to replace them, believe it or not a key feature vital to a long duty life. Heavy duty pump-100% duty rating (use it all day long continously) check other compressors for duty rating, some are 50% so for say 5 hours on, you need about 5 hours off, or you'll be looking for another compressor shortly if you push them too hard. Heavy duty frame/roll bar design to take jobsite abuse. recessed gauges-keeping components away from damage (it looks like the regulator knob could snap off easily though.

I would buy it again for sure, because if I bought a smaller lighter unit, (like I was initially looking for) I would have been left high & dry because, as luck would have it my large compressor broke the day before, & the Bosch substituted fine for finish & light framing & siding work that had to get done.