Bosch TS1002 Table Saw Rear Outfeed Support Extension

by Bosch

Product Description

Amazon.com Product Description

Bosch TS1002 extends 18-inches and stores flush to table. It extends the working depth of Bosch 4000 10-inch table saw. It features hardened metal construction; aluminum mounts and includes 1 table saw extension. The table saw is not included. This product also has a 1-year warranty.

Product Description

Table saw rear outfeed support extension. Extends 18-inches and stores flush to table; extends working depth of Bosch 4000 10-inch table saw. Hardened metal construction; aluminum mounts. Includes 1 table saw extension; table saw not included. 1-year warranty

See all Product Description

Product Details

• Shipping Weight: 8.6 pounds (View shipping rates and policies)
• Shipping: This item is also available for shipping to select countries outside the U.S.
• Shipping Advisory: This item must be shipped separately from other items in your order. Additional shipping charges will not apply.
• ASIN: B00004R5S0
• California residents: Click here for Proposition 65 warning.
• Item model number: TS1002
• Average Customer Review: 4.3 out of 5 stars  See all reviews (57 customer reviews)
• Amazon Best Sellers Rank: #1,770 in Home Improvement (See Top 100 in Home Improvement)
  • #2 in Home Improvement > Power & Hand Tools > Power Tool Accessories > Saw Accessories > Table Saw Accessories

Customer Reviews

Most Helpful Customer Reviews

103 of 104 people found the following review helpful:

5.0 out of 5 stars Video review to clear up conflicting information, September 24, 2009

By 

Samuel Curren "TelegramSam" (Lehi, UT) - See all my reviews
(REAL NAME)   

Amazon Verified Purchase

This review is from: Bosch TS1002 Table Saw Rear Outfeed Support Extension (Tools & Home Improvement)

Length:: 3:58 Mins

There seem to be plenty of conflicting reviews on both the left side extension and the outfeed extension, and I've made this video to clear them up. Issues cleared up:
- The front bar for the left side extension is short enough to not hit the red lever for the right side extension.
- Both left side extension and outfeed extension come with a stop knob for securing the extensions either open or closed.
- Both extensions sag just a little, which I fixed by placing a washer (approx 0.043 in thick) between the brace and the tablesaw for the _back_ bolt on each bracket. This modification brought it very close to level, for just over $2 in washers at my local big box hardware store.

I do say a few odd words here and there in the video (quarters when I meant washers, etc.) But I'm sure you can figure it out.

Overall review: These were what I expected, fit my 4100 series Bosch worksite table saw, and were easy to install following the included instructions.

50 of 51 people found the following review helpful:

4.0 out of 5 stars outfeed support, January 29, 2002

By A Customer

This review is from: Bosch TS1002 Table Saw Rear Outfeed Support Extension (Tools & Home Improvement)

The outfeed support is a handy thing to have on a table saw. The only problem that I have encountered in useing it is that flexible materials like thin plywood tend to flex between the saw and the outfeed support and hit the support instead of going on top of it. This problem can be fixed by using a peice of scrap as a 'brige' to help the material make it onto the suport.

32 of 32 people found the following review helpful:

3.0 out of 5 stars mike in maine, October 22, 2007

By 

Michael R. Golden - See all my reviews
(REAL NAME)   

This review is from: Bosch TS1002 Table Saw Rear Outfeed Support Extension (Tools & Home Improvement)

After reading some of the poor reviews for this product I had some reservations.When I unpacked and assembled the extention I soon discovered the problems others had described.1st the miter guide slots don't align with the notches in the extention.2nd the sliding rails are too far apart, one owner had elongated the mounting holes to address this.The actual problem is in the illustrations in the instructions! The pictures of the model 4000 saw and the 4001 saw are reversed.Simply mount one bracket facing outward[the one with the lock knob]and the other facing inward,as pictured for the model 4001,and the extention fits and operates smoothly! Perhaps BOSCH should correct the instructions instead of agreeing they had made a manufacturing error to appease a dissatisfied customer. I hope this helps others who encounter this problem.