From the Manufacturer
The Xs Series of power amplifiers from Crown represents a new era in affordable, quality power amplification. The line consists of four models in a uniform, rugged 2U chassis, incorporating the best of tried-and-true design principles and innovative features. The Xs1200 has the following power ratings at 1 kHz:
- 900 watts - 2 ohm dual (per channel)
- 750 watts - 4 ohm dual (per channel)
- 450 watts - 8 ohm dual (per channel)
- 1900 watts - 4 ohm bridge
- 1645 watts - 8 ohm bridge
Features - Housed in a rugged, all-steel 2U chassis.
- Efficient forced-air fan prevents excessive thermal buildup.
- 2-channel models have XLR-1/4" combo inputs, 3-pin Phoenix-style inputs, daisy-chain XLR outputs, touch-proof binding post outputs and Speakon outputs. Xs4300 has XLR-1/4" combo inputs and touch-proof binding post outputs.
- Precision detented level controls, power switch, and five LEDs which indicate clip for each channel, power, AC mains, temperature and fault conditions.
- Microprocessor-controlled protection system.
- Three-Year, No-Fault, Fully Transferable Warranty completely protects your investment and guarantees its specifications.
Technical Specifications
- Sensitivity (volts RMS) for full rated power at 4 ohms: 1.4V Frequency Response (at 1 watt): 22 Hz to 22 kHz: 1 dB.
- Phase Response (degrees at 1 watt, 20 Hz to 20 kHz): +5, 18
- Signal-to-Noise Ratio: A-weighted, below rated power: > 102 dB. 22Hz to 22kHz, below rated power:> 97 dB.
- Total Harmonic Distortion (THD) at full bandwidth power, from 20 Hz to 20 kHz: 0.5%.
- Intermodulation Distortion (IMD): (60 Hz and 7 kHz at 4:1) from full rated output to 40 dB: < 1%.
- Damping Factor (8 ohm) 10 Hz to 400 Hz: > 200.
Controls
- Level: Two or four front-panel, gray rotary level controls, one for each channel.
- Power: Front-panel switch; on when in the right-hand position.
Indicators
- Signal: Two or four green LEDs, one for each channel, illuminates when the channels input signal level is above 40 dBu.
- Clip: Two or four front-panel red LEDs, one for each channel, illuminates when the channels output signal is being overdriven.
- Power: Yellow front-panel LED indicates amplifier has been turned on and AC power is available.
- AC Mains: Red front-panel LED indicates the presence of AC power at the power cord, even if the amplifier is not turned on.
- Fault: Red front-panel LED illuminates when amplifier is in protect mode. Also illuminates briefly during normal power-up when amplifier is first switched on.
- Bridge: Yellow LED indicates that amplifier is in bridge mode (Channels 1 and 2, Channels 3 and 4 in Xs 4300).
- Temp: Red LED indicates that channel(s) are in thermal protect mode.
Input/Output
- Input Connectors:XLR-1/4" combo connectors: One per channel, 3-pin female XLR connector and TRS 1/4" phone jack accept balanced or unbalanced signals. 3-pin Phoenix-style connectors (2-channel models only): One per channel, accepts balanced or unbalanced signals.
- Input Impedance (nominal) balanced, unbalanced: 20 k ohms, 10 k ohms.
- Output Connectors: Balanced XLR connectors (2-channel models only): One per channel, 3-pin male XLR connector in parallel with XLR-1/4" combo and Phoenix-style input connectors for daisy-chain operation. 5-Way binding post output connectors: One pair per
Product Description
The Xs 1200 is the highest-powered model in Crown's Xs series, providing 1,100 watts per channel into 4 ohms for customers demanding more power within the Xs Series.