Frequently Bought Together
Product Features
|
Product Details
Would you like to give feedback on images?
|
Product Description
The Cuisinart SPB7-20TXN Blender Blade Driver Clutch fits models BFP703 BFP-703 BFP703B BFP-703B BFP703CH BFP-703CH SPB-7 SPB7 SPB-7BK SPB7BK SPB-7CH SPB7CH SPB-7BC SPB7BC CB7 CB8 CB9 BFP-703BK BFP703BK CB-9 CB9 FPB-5PC BFP703R BFP-703R CB-3 CB-5 CB-6 CB-7 CB-8 CB-18 CBT-500 CBT-600 SPB-3 BC-56 CB-600FPPC CB-600PC FPB-5PC1
Customer Reviews
Most Helpful Customer Reviews
29 of 29 people found the following review helpful
I thought I was going to have to throw out this blender since I couldn't find this part anywhere on Cuisinart's site, that is until I found it here on Amazon! This part took UNDER 5 minutes to replace.
Remove 3 screws on the bottom of the blender
Pull off cover
Use a screwdriver to keep the motor's shaft from spinning
On the other side, use a wrench, grab and unscrew the brass ring in a clockwise motion (It's reverse threaded)
Screw on new replacement blade driver (Counter-clockwise to tighten)
Put blender cover back on
Reinstall the 3 screws on the bottom of the blender
You're done!
I'm serious when I say that the whole process took me about 3 minutes.
REALLY beats having to buy a new blender.
Remove 3 screws on the bottom of the blender
Pull off cover
Use a screwdriver to keep the motor's shaft from spinning
On the other side, use a wrench, grab and unscrew the brass ring in a clockwise motion (It's reverse threaded)
Screw on new replacement blade driver (Counter-clockwise to tighten)
Put blender cover back on
Reinstall the 3 screws on the bottom of the blender
You're done!
I'm serious when I say that the whole process took me about 3 minutes.
REALLY beats having to buy a new blender.
9 of 9 people found the following review helpful
Fyi, the brass plate has reverse threads. So the rule of, righty tighty and lefty loosy, do not apply in this case. Try turning the brass threads to the right to take it off and maybe you can then use the replacement clutch. GOOD LUCK, I hope this helps.
8 of 8 people found the following review helpful
I concur with the earlier review entitled "Don't get this unless you can remove the brass" - sadly I did not realize what this reviewer meant until I received the piece and found that on the bottom side, not shown in item image on website, that there is a redundant brass threaded hole permanently glued in. I really cannot remove the brass piece and so I cannot use this replacement part.
Most Recent Customer Reviews
GOOD PART
THE PART FUNCTIONS PROPERLY, BUT IT'S NOT QUITE AS EASY TO REMOVE AS SOME REVIEWS MAY LEAD ONE TO BELEIVE. Read more
Published 10 days ago by KODIAK
expensive little piece of plastic
Expensive little piece of plastic but that beats having to buy a new blender. Removing the broken one to replace it can be challenging though and it will break again, it's just a... Read more
Published 13 days ago by Philippe Gadeyne
Blender Blade driver Clutch
Amazon.com made it easy for me to find this small item for my broken Cuisinart blender, model SPB7. For just few dollars the blender blade driver clutch saved me from buying a new... Read more
Published 6 months ago by Monique Marti
Easy Fix
The replacement part arrived as promised and after reviewing the video on how to replace the part it was a piece of cake. I highly recommend this part purchased through Amazon. Read more
Published 7 months ago by Dennis Mansmith
Easy replacement, works great.
Took less than 10 minutes to swap out my broken clutch with this new one. The key thing to know is that it has reverse threads (righty loosey, lefty tighty). Read more
Published 9 months ago by Dan Chan
Saved my blender!
Thanks R. Celin, your instructions were right on! I followed them to a tee and my blender was fixed in minutes. Read more
Published 13 months ago by lds247ru2
Good Part but how about some instructions?
If it wasn't for the helpful instructions left by some of the reviewers here on Amazon, it would have taken me a long time to figure out the installation on this. Thanks everyone.
Published 17 months ago by Gazamoon
Arrived Quickly
Not much to say about a blender part. It was the correct one and arrived promptly.
Published 20 months ago by writeseth
Don't forget the WD-40!!!
After removing the bottom assembly, I tried removing the brass ring from the previous assembly, and was unable to provide enough torque by turning the bottom screw on the motor... Read more
Published 21 months ago by Hokie
Solid replacement for broken part
This was a solid replacement for the broken part of my blender / food processor. I had to remove the 3 bottom screws of the blender case to open it up, then I turned the screw... Read more
Published 21 months ago by T. Fleming
Customer Discussions
|
This product's forum
Active discussions in related forums
Search Customer Discussions
|
Related forums
|
Look for Similar Items by Category
|
