DELTA 31-695 6-Inch/9-Inch 1HP Open Stand Belt/Disc Sander

Other products by DELTA

Product Description

Amazon.com Product Description

The DELTA 31-695 6-Inch/9-Inch 1 HP Open Stand Belt/Disc Sander includes an adjustable 80-grit abrasive belt unit that operates vertically, horizontally, at an angle, or can be removed for contour sanding jobs. The sander is powered by a 1 HP, 120-volt induction motor, which runs a 9-inch disc sander that spins at 2,800 RPM. The 48-by-6-inch adjustable belt is kept in aligned by an easy-to-use belt tracking knob. It cycles at 2,200 square feet per minute across a graphite pad that reduces friction heat and preserves belt quality and life. The cast-aluminum worktable includes a miter gauge slot and tilts at 45 degrees for versatile surface work. The sander also includes a 2-1/4-inch dust port that connects to a standard shop vacuum and a steel stand with non-slip pads.

From the Manufacturer

DELTA 31-695 6-Inch/9-Inch 1 Horsepower Open Stand Belt/Disc Sander, 1

Product Details

• Product Dimensions: 29 x 16 x 15 inches ; 91.5 pounds
• Shipping Weight: 90.2 pounds (View shipping rates and policies)
• Shipping: This item can only be shipped to the 48 contiguous states. We regret it cannot be shipped to APO/FPO, Hawaii, Alaska, or Puerto Rico.
• Shipping Advisory: This item must be shipped separately from other items in your order. Additional shipping charges will not apply.
• Note: Gift-wrapping is not available for this item.
• ASIN: B00002236D
• California residents: Click here for Proposition 65 warning.
• Item model number: 31-695
• Average Customer Review: 3.6 out of 5 stars  See all reviews (29 customer reviews)
• Amazon.com Sales Rank: #12,166 in Home Improvement (See Bestsellers in Home Improvement)

  Popular in this category: (What's this?)

  #4 in

  Home Improvement > Power Tools > Sanders > Combination Disc & Belt Sanders

• Discontinued by manufacturer: Yes

Customer Reviews

Most Helpful Customer Reviews

61 of 62 people found the following review helpful:

3.0 out of 5 stars Works OK, but could be better., November 17, 2002

By	J. Joswick "Jeff's Custom Woodworking" (Dannemora, NY United States) - See all my reviews (REAL NAME)

I needed a stationary sander, and Delta's 31-695 was the unit that was in my price range. It went together well, and sands satisfactorily, but just seems to lack something. I didn't want to spend the nearly $800 for the Delta sanding center, but in the long run..., I probably should've held out. The cast aluminum table for the disc sander is flimsy, and does not adjust well to angled sanding. I've already stripped out one of the retention knobs and have noticed a little difficulty with belt tracking. Other than those issues, it's OK, I wouldn't purchase another one though.

51 of 52 people found the following review helpful:

5.0 out of 5 stars Great Tool, August 17, 2000

By	Kenneth Hurst (Plano, TX United States) - See all my reviews

I purchased this sander as an upgrade to my 4" belt / 6" disk sander. The smaller unit worked fairly well but was underpowered and sometimes I could stop the belt. The sanding belt always seemed to be a little too narrow. This unit seems right on the money.

I use it to sand a lot of scroll saw projects (stackable baskets, collapsible baskets, ornaments, candle holders, puzzles, etc.) I can place the wood on the belt next to the stop and hold it down with a push block. I then turn the sander on. That gives me complete control over sanding 1/8" to 1/4" thick material without sanding my fingers or pinching them. The 1 HP motor has plenty of power to start up under a load. I also have the accessory fence unit. This allows me to sand large areas flat that were cut with a scroll saw. The disc is excellent for smoothing out curves and removing burn marks. This is a must have tool if you do a lot of scroll sawing. I even use it for finish sanding using a 220 grit belt. I also use it for sanding finger joints flush on oak, maple and poplar boxes. One final use is sanding smaller cupped stock flat for use as sliding box lids.

You can sand puzzles easily by placing on the belt before starting and holding the pieces with the push block. You can sand off pattern paper. You can shape up the edges on collapsible baskets and remove blade burn marks. You can smooth out and flatten large edges. Interestingly enough, I have yet to use the edge of the belt to sand.

The tool is noisier than the 4/6 unit. I would compare its noise level as slightly louder than my Delta 14" band saw. It is not bad but I would suggest using hearing protection. The unit runs very smoothly. The belts take a little time to change -- especially with the accessory fence attached -- but the process is easy. The supplied 80 grit belt and disc are a little too aggressive for scroll saw projects. I replaced them with finer grits.

41 of 42 people found the following review helpful:

1.0 out of 5 stars Nice try, November 10, 2001

By	Kevin (Bronson, MI United States) - See all my reviews

Like the othert Delta products I have purchased.. I was excited when my new sander arrived. It assembled well, and looked impressive. Until I snapped the power switch and the motor would not turn. Smoke came out of the motor. I shut the unit down, and double checked everything, again! The motor turned freely by hand, but turn it on. and it would lock. Called support, 30 days later recieved a new motor and installed it. This motor started right up and as I almost got excited, it slowed and stopped. Then did the same thing as the first! I boxed it up, and sent it back. 2 failed motors, over 30 days, and I was still not able to use it! No thank you! Hope this helps!