DELTA 46-250 Midi-Lathe

by Delta

Product Description

From the Manufacturer

Delta 46-250 Midi-Lathe

Product Details

• Product Dimensions: 30 x 19.5 x 12 inches ; 85 pounds
• Shipping Weight: 93.3 pounds
• Shipping: This item is also available for shipping to select countries outside the U.S.
• Shipping Advisory: This item must be shipped separately from other items in your order. Additional shipping charges will not apply.
• ASIN: B00004R9LL
• California residents: Click here for Proposition 65 warning.
• Item model number: 46-250
• Average Customer Review: 4.2 out of 5 stars  See all reviews (6 customer reviews)
• Amazon Best Sellers Rank: #750,724 in Home Improvement (See Top 100 in Home Improvement)
• Discontinued by manufacturer: Yes

Customer Reviews

Most Helpful Customer Reviews

90 of 92 people found the following review helpful:

5.0 out of 5 stars The best of the two, December 12, 2000

By 

Eddie Avedikian (Los Angeles, CA USA) - See all my reviews

This review is from: DELTA 46-250 Midi-Lathe (Tools & Home Improvement)

The differences between the JML-1014 and the Delta 460-250 was very clear when I compared them side by side. Hands down the Delta was the winner. The quality of the workmanship, the close tolerances, the final milling of all the parts were very evedent. Other differences are as follows: The access panel for the upper pulley on the Jet is very inconvenient. Its in the back, making it difficult to access when the machine is mounted on a bench. The delta access panel is mounted in the front, very easy access, quick and simple. What a pain it was to change pulleys on the Jet. The power switch on the Delta is conveniently mounted on the left side of the machine. Two advantages here, you can hit the switch with your left hand with out having to put down the cutting tool (in your right hand) as you do with the Jet, because it's power switch is on the right. Secondly, the switch is located very close to the rotating arbor, which is a good thing, it allows you to grab a hold of it and slow/stop it just after you turn the switch to off. I found this to be a big plus when you are constantly shuting down the machine to look at your work with out having to wait before it spools down or having to change hands to do it. The motors are rated at 1/2 hp each but the Delta draws more amperage. I felt the difference when I turned on each machine while trying to hold onto the arbor. The Delta had more torque (and I was fair about it because I put each machine in its lowest speed/pulley posisiton). The Delta is a heavier unit which adds to the stability when you are first taking down a square piece of stock. A heavier machine always helps with chattering. The jet will always be limited to a 14" piece of stock, the Delta is expandable with an optional tail piece that is available if your needs grow. Also, I have never had problems getting parts for my other Delta tools, I expect it will be the same with this lathe. I'm sure the jet is a good tool, but you will never notice the differences unless you compare them side by side as I did. My pick is the Delta, besides, its ...cheaper.

50 of 50 people found the following review helpful:

5.0 out of 5 stars Delta 46-250 vs. Jet JML-1014, March 7, 2001

By 

Jim (Dayton, Ohio) - See all my reviews

This review is from: DELTA 46-250 Midi-Lathe (Tools & Home Improvement)

I own both the Delta and Jet. I use both for turning pens, small bowls, tool handles, etc. The weight, construction, fit, finish, power, and noise are very close. I don't feel that either has an advantage over the other in those categories. The differences are in the convenience of speed change. The Delta has front access to the upper spindle; whereas the Jet has a, somewhat awkward, rear access. Also, the Jet has an annoying spring-loaded side door for the lower spindle. It is so difficult to operate,that I modified mine to a more conventional snap type which is found on the Delta. The power switch is located on the lower right on the Jet and above the upper spindle on the Delta. I think the preference is the Delta because, I am right handed and can manipulate it with my left hand while holding a chisel with my right. The Delta makes provision for adding an accessory extension bed for turning longer stock. It is approximately $50.00 and easily bolts up to the lathe. I use both lathes and enjoy them equally. I don't hesitate to recommend either machine as both are quality products. If I could only have one, I would choose the Delta based upon the convenience of speed changes, power switch, and the ability to add the bed extension.

32 of 33 people found the following review helpful:

4.0 out of 5 stars Best Mini Lathe Value, October 14, 2001

By 

John M. (Riverside, CA United States) - See all my reviews

This review is from: DELTA 46-250 Midi-Lathe (Tools & Home Improvement)

After carefully studying both the Jet JML 1014 Mini Lathe and the Delta 46-250 Midi Lathe, I decided to purchase the Delta. I'm glad I did. Both machines are well designed and very well made, but the Delta simply offers the best value for a quality lathe in this class. It is slightly larger and heavier than the Jet, which helps dampen vibration and enhances stability, especially when roughing out spindles and bowl blanks at slower speeds. Other advantages include more convenient belt access than the Jet for quicker and easier speed changes, and an available cast iron bed extension that increases the spindle capacity of this machine to 37 inches. The fit and finish on the Delta is excellent in spite of its Chinese origins (the Jet is made in Taiwan) and the layout of the machine indicates a greater attention to ergonomics than the Jet. None of this is meant to suggest that the Jet is an inferior machine. Quite the contrary, the Jet JML 1014 is a superbly made machine and a first-rate performer. It certainly will not disappoint anyone who purchases one. But at a price that is at least $30 higher than the Delta in most places, and with fewer conveniences, it simply doesn't offer the same value as the Delta. I do have one small beef with the Delta, however. For all the care and workmanship that obviously went into the design and manufacture of this machine, I'm disappointed that Delta chose to use plastic handles for the tool rest and motor tension adjustment bolts. These handles have a cheaper and flimsier feel than the cast metal handles that come with the Jet lathe, and they have the added disadvantage of being in places where they will receive plenty of wear and tear. Also, the headstock belt pulley cover on the Delta lathe, while more conveniently located than the one on the Jet, is made of a flimsy plastic and sports a large protruding knob that some turners might find annoying. I pay attention to small details like this when looking at Delta machines because my experience with Delta customer service in recent years has shown that replacement parts for their machines, even such small items as plastic knobs, are usually outrageously overpriced and at times difficult to obtain without lengthy delays due to backordering. If these parts break prematurely (as they are very apt to do), replacing them could be something of a nuisance. Still, with a two year product warranty, excellent fit and finish, superb performance, easy expandability and a price that beats their toughest competitor, this machine is simply the best value you're likely to find in a mid-size lathe.