HTC HTT-31 Tool Table

by HTC

Product Description

From the Manufacturer

The HTC HTT-31 patented Tool Table is constructed of heavy gauge steel and features a 14-Inch by 25-Inch by 1-Inch expandable MDF top with a handy ruler imprinted on the surface. It also features a 18-Inch by 27-Inch MDF lower shelf, rubber feet for non-skid support, and a tough, powder coat finish. With a working height of 31-Inch and capacity of 500-Pound, the HTT-31 is the perfect tool table for all your workshop needs.

Product Description

Heavy gauge steel construction with expandable 14" x 25" MDF top and working height of 31". 500 lbs. capacity.

Product Details

• Product Dimensions: 24 x 14 x 5 inches
• Shipping Weight: 27.5 pounds (View shipping rates and policies)
• Shipping: This item is also available for shipping to select countries outside the U.S.
• Shipping Advisory: This item must be shipped separately from other items in your order. Additional shipping charges will not apply.
• ASIN: B00065UHP2
• California residents: Click here for Proposition 65 warning.
• Item model number: HTT-31
• Average Customer Review: 3.9 out of 5 stars  See all reviews (10 customer reviews)
• Amazon Best Sellers Rank: #16,519 in Home Improvement (See Top 100 in Home Improvement)
  • #41 in Home Improvement > Power & Hand Tools > Power Tool Accessories > Stands

Customer Reviews

Most Helpful Customer Reviews

7 of 7 people found the following review helpful:

1.0 out of 5 stars Obnoxiously Bad, June 30, 2011

By 

El Guapo (New York, NY) - See all my reviews

Amazon Verified Purchase

This review is from: HTC HTT-31 Tool Table (Tools & Home Improvement)

Having received the table this afternoon, I am absolutely stunned that it has ever received a good review. Let me preface my comments by pointing out that I am not whatsoever unfamiliar with assembly projects. I've assembled my beds, my bandsaw, the three desks in our home, all of the shelving in my work space, countless pieces of furniture, etc. But this thing is truly idiotic in its assembly planning. It's not that it's complicated - it's very intuitive and straightforward if you know what the finished assembly looks like, as it is ultimately a very simple construction. The problem is the unnecessarily awful assembly components ("unnecessary" because it wouldn't cost a penny more to simply provide bolts with square collars and put square, rather than round, holes in the legs and beams). The legs and support beams are attached to one another with nuts on one side and a phillips head on the other. Strike one. Tightening these things adequately is infuriatingly difficult because the phillips heads will strip almost immediately if you get anywhere CLOSE to tight... And from that point on, you'll spend the rest of the assembly attempt fighting off insanity as this thing constantly collapses under its own weight while you're trying to hold it steady enough to insert the next bolt/washer/nut set that will be impossible to tighten. And when you're through, you'll have a rickety piece of junk I wouldn't trust to hold my lunch. I'm throwing it out. I'm so annoyed with this thing, I can't even be bothered to disassemble it and go through the hassle of trying to get a refund. Buy this lemon at your own risk.

2 of 2 people found the following review helpful:

4.0 out of 5 stars Decent Tool Stand, February 19, 2011

By 

Christopher Pinzone - See all my reviews

This review is from: HTC HTT-31 Tool Table (Tools & Home Improvement)

This is a decent tool stand. I bought it to use with a Delta Midi lathe. I bolted a heavy 1 & 1/2 inch particle board & laminate top to it which gave the whole thing a lot more mass. It is tough to get the unit to sit level without having leveling feet. I also bolted a heavy duty drawer to the bottom of the unit and I think that is when the whole thing went slightly out of square giving me a little tilt when the unit sits on the floor. A thin piece of shim stock fixed the problem quickly. The metal of the stand is not exactly heavy but sturdy enough so the unit doesn't move when operating the lathe. The lathe stand costs in the neighborhood of $175 so this turned out to be a much better alternative.

2 of 2 people found the following review helpful:

5.0 out of 5 stars Pleased with purchase, August 29, 2010

By 

Leonard R. Payne "KG4YOL" (Jasper, Ga. USA) - See all my reviews
(REAL NAME)   

Amazon Verified Purchase

This review is from: HTC HTT-31 Tool Table (Tools & Home Improvement)

I use this table with a DP121L Ryobi drill press. This is a very large and heavy bench top tool. The height and base is just about perfect for this tool.