Kreg SML-C125 1-1/4-Inch No. 2 Coarse Screw (1000-Pack)

by Kreg

Product Description

Amazon.com

Kreg's self-tapping screws were designed for its famous pocket-hole joinery, but that's not all they're good for. Kreg's self-tapping auger point eliminates time-consuming pre-drilling, and these screws are made from the highest quality steel, case-hardened and coated with a dri-lube finish. That means less driving torque for you. This coarse-thread screw has a larger thread diameter and provides greater holding power when driving a screw into soft material such as plywood, particle board, MDF, melamine and pine. The washer head offers a great surface area to seat the screw firmly and helps prevent overdriving. They're on the spendy side, but the quality is worth it.--Kris Jensen-Van Heste

From the Manufacturer

No. 8, 1-1/4-inch Coarse Screw (softwood to softwood). 1000 pack.

Product Details

• Shipping Weight: 5.4 pounds (View shipping rates and policies)
• Shipping: This item is also available for shipping to select countries outside the U.S.
• ASIN: B00002240N
• California residents: Click here for Proposition 65 warning.
• Item model number: SML-C125 - 1000
• Average Customer Review: 4.7 out of 5 stars  See all reviews (25 customer reviews)
• Amazon Best Sellers Rank: #1,485 in Home Improvement (See Top 100 in Home Improvement)
  • #3 in Home Improvement > Hardware > Nails, Screws & Fasteners > Screws
  • #5 in Home Improvement > Power & Hand Tools > Power Tool Accessories > Jigs

Customer Reviews

Most Helpful Customer Reviews

79 of 79 people found the following review helpful:

5.0 out of 5 stars You need the coarse AND the fine screws, February 23, 2004

By 

Bob Feeser "MillCrafters.com" (Springfield, PA USA) - See all my reviews
(VINE VOICE)    (TOP 1000 REVIEWER)   

Amazon Verified Purchase

This review is from: Kreg SML-C125 1-1/4-Inch No. 2 Coarse Screw (1000-Pack) (Tools & Home Improvement)

I had read a review that stated they were using the fine screws for everything. I found that when using soft pine, and more importantly into plywood, the fine screws were on the edge of getting the job done. All you had to do was remove one of the screws and reinsert it, to see what I mean. In my opinion getting the coarse screws, and the fine screws is essential.
These screws have a very sharp tip on them, and the shaft thickness is thin as well. Consequently you do not need to pre-drill unless you are using them close to an edge of a soft wood. In that condition the thin edge can bulge a little.
The great thing about pocket hole screws is their convenience, and strength especially when used in pairs. You will find your self using these more and more often. I even use them on straight joinery by drilling with a forstner bit to create a straight pocket, then go right in with the pocket hole screws. Admittedly by using the kreg jig, and getting an angled installation is stronger than going in straight. The angle prevents tugging on just the threads, but rather creates strength by having to pull the angled shaft through the wood. That is a lot stronger except in the rare condition of pressure being exerted at the direct angle of insertion-not likely.
Their is some difference of opinion as to whether it is advisable to use glue in conjunction with pocket hole screws. One camp states that since the screws hold so well when done in pairs, that you do not need to use glue. Additionally, that gives you the option of being able to remove the joint, in the event you need to resize for example, or disassemble for shipping. Additionally their argument states that since the pocket hole screw system holds so tight, any glue that is put in the seam will be squeezed out.
The other camp feels that for security purposes, gluing and screwing is the way to go. In the book, "Building Kitchen Cabinets" by Udo Schmidt (an excellent book by the way) the author states, "The expense of a pocket hole-drilling jig will easily be repaid in the time you save assembling face frames.
So if you are contemplating getting the Kreg jig assembly, it comes highly recommended. If you are thinking about buying the screws, I recommend you getting the coarse and fine screws in the 1 1/4" format, since they are useful for joining 3/4" wood. Additionally you should get the screw kit with a variety of different length screws for those times when you are dealing with different stock thickness.
In a recent magazine doing a run off of different manufacturers pocket hole jigs, Kreg took first place in every size jig-first place across the board. Hope this helps.

19 of 19 people found the following review helpful:

5.0 out of 5 stars Can be used for many other projects too!, May 5, 2006

By 

John E. Pombrio "John Pombrio" (Manchester, CT United States) - See all my reviews
(REAL NAME)   

Amazon Verified Purchase

This review is from: Kreg SML-C125 1-1/4-Inch No. 2 Coarse Screw (1000-Pack) (Tools & Home Improvement)

These are great screws in their own right. I love them for pocket hole joinery but I also am using them to hang new windows. The self tapping is terrific, the pan head does not go through the plastic flashing, the the square drive holds the screw securely while I am one handed drilling them while hanging onto the ladder! I do not think they are weatherproof but after flashing and the trim, they will be protected enough. High quality screws, never have had one strip one me and the self tapping has NEVER caused the board to split even right near the edge.

24 of 27 people found the following review helpful:

5.0 out of 5 stars Self Boaring!, April 17, 2001

By 

yuvak tuladhar (Richmond , CA) - See all my reviews
(REAL NAME)   

This review is from: Kreg SML-C125 1-1/4-Inch No. 2 Coarse Screw (1000-Pack) (Tools & Home Improvement)

These screws work really good with Kreg's drill bit with pilot hole tip (3/8" diameter). It is self boaring so it doesn't split the wood. The coarse one works for soft wood like pine and plywood. Use fine screws for hard wood. Wish these screws were a little cheaper.