Makita MAC2400 Big Bore 2.5 HP Air Compressor

by Makita

• Oil lubricated: Cooler running pump, minimizes wear
• Durable cast iron cylinder reduces wear and increases pump life; removable for easy maintenance
• Built-in thermal overload for additional motor protection
• Large automotive style industrial air filter for increased air intake and greater efficiency
• One-year manufacturer's warranty

Product Description

Amazon.com

Makita's 2.5HP Air Compressor is equipped with Makita's Big Bore engineered pump cylinder and piston for higher output for two nailers, with less noise and improved job site performance. The MAC2400 delivers industrial power and results with improved durability under tough job site conditions.

View larger

MAC2400 Features PERFORMANCE - Cast-iron cylinder with greater bore and stroke for maximum performance DURABILITY - Runs at a lower RPM (1,720) resulting in greater motor and pump life RELIABILITY - Low AMP draw reduces instances of tripped breakers CONVENIENCE - Oil drain and oil sight glass conveniently located for easy access and maintenance INCLUDES - Oil and 1/4" universal quick coupler

Tool Specifications Horsepower 2.5 Pump Oil-lubricated Tank 4.2 "Twin Stacked" gal. Performance 90 PSI: 4.2 cfm 40 PSI: 4.8 cfm Maximum Pressure 0 - 130 PSI AMPS 12.3 Noise Level 79 dB Size 19-3/8"x18-3/4"x18" Net Weight 77 lbs.

2.5 HP with Big Bore Engineered Pump
The MAC2400 is powered by a 2.5 HP motor. The Makita Big Bore engineered pump with cast iron cylinder has greater bore and stroke for increased compression, faster recovery and less noise. The cast iron construction is engineered for increased durability even under tough job-site conditions. The MAC2400 has an oil-lubricated pump and is equipped with a large automotive style filter for increased air intake and greater efficiency. The Big Bore oil-lubricated pump is also more efficient: the MAC2400 runs cooler and at half the RPM of most competitive units, resulting in greater motor and pump life and lower noise. The 4.2 gallon twin-stacked tank sustains an operating pressure of 130 PSI, and delivers 40PSI (4.8 CFM) and 90 PSI (4.2 CFM), enough for two nailers. The low AMP draw reduces instances of tripped breakers and voltage drop that can cause premature motor failure. The roll bar handle provides portability and additional protection, helping it withstand harsh jobsite environments. Additional features include a convenient oil drain and oil sight glass, a tank drain valve that supersedes standard petcock design for easier maintenance, and finned discharge tubing that dissipates heat more efficiently.

Versatile Design for a Range of Applications
The MAC2400 is engineered for low noise, high output and less maintenance, and delivers industrial power and results with improved durability under tough job site conditions. The MAC2400 is just another example of Makita's commitment to innovative technology and best-in-class engineering.

About Makita Big Bore Air Compressors
Makita Big Bore Air Compressors deliver higher output and less noise for improved job site performance. The Makita Big Bore engineered pump with cast iron cylinder has greater bore and stroke for increased compression, faster recovery and less noise. The cast iron construction is engineered for increased durability even under tough job site conditions. All Makita Big Bore Air Compressors are oil lubricated and equipped with large automotive style filters for increased air intake and greater efficiency. Makita Big Bore Air Compressors deliver industrial power and results with improved durability.

About Makita
Makita is a worldwide manufacturer of industrial quality power tools and offers a wide range of industrial accessories. Makita applies leading-edge innovation to engineer power tools that are more compact and energy efficient, yet deliver industrial strength power and results. Makita U.S.A., Inc. is located in La Mirada, California, and operates an extensive distribution network located throughout the U.S. For more information, please call 800/4-MAKITA (800/462-5482) or visit makitatools.com. Makita is Best in Class Engineering.

Warranty
Every Makita tool is thoroughly inspected and tested before leaving the factory. If you are not satisfied with any Makita tool within 30 days of purchase, return it and Makita will provide a replacement or refund. Each Makita tool is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one-year period, return the COMPLETE tool, freight prepaid, to one of Makita's Factory or Authorized Service Centers. Please see makitatools.com for complete details.

What's in the Box
Makita MAC2400 2.5 HP Air Compressor, oil and 1/4-inch universal quick coupler.

From the Manufacturer

The new MAC2400 - Twin Stack air compressor by Makita is blowing away the competition. With built-in features such as a super quiet motor that draws only 12.3 amps to operate, a lower 1720 RPM rating and a heavy duty Intake Air Filter system like no other, its easy to see how this unit will out last and outperform everyone else. It delivers 4.2CFM @ 90PSI and is equipped with a lever handled ball valve drain system to get rid of condensation build up in the tank . The exclusive finned discharge tubing increases heat dissipation while reducing moisture in the lines and the easily removable cast iron cylinder reduces wear for increased pump life. High quality, maximum performance - just what you expect from Makita.

Most Helpful Customer Reviews

202 of 204 people found the following review helpful

5.0 out of 5 stars Best in class October 4, 2005

By Michael D. Brill

I think it's the best for the following:

A) This compressor just purrs. People are amazed when it's running. Big rubber feet also help prevent transmitting vibration to whatever it's sitting on, so no more vibrating boards.

B) Over-built compressor compared to tank size - so cycle times are very short - if using light-duty tools, it doesn't run much anyway. Also runs way more cool than others - I'll save those sear lines for my steak on the grill - not my forearm.

C) No leaks - holds its air pressure seemingly forever when turned off (not that you shouldn't release pressure when done using it).

D) The air filter is a miniature version of an old-time car air filter. For a unit that's going to be sitting on the ground amidst swirling construction dust, this is a big plus.

E) It does indeed weigh in, but at least the design is very compact. The frame wraps around and protects most of the important stuff, so there are no lines, wires, etc. waiting to be snagged. The glaring exception is the air filter hanging off the side - I can see this part's going to be replaced at some point when I throw it in a truck bed. No problem for shop use though.

Be forwarned - Makita's packaging designers always seem to get it 90% right. In this case, the air filter is just thrown in loose inside the box - mine broke one of the gauge glasses. If pressed, their warrantee dept. will send out small parts, but it's a PITA to get a product this good only to have to fix it right out of the box. Also - pay attention to the "break-in" procedure - run it for @30 minutes with no load, open petcock, to seat the rings.

298 of 305 people found the following review helpful

5.0 out of 5 stars The other Reviews are Correct, this is a great compressor September 16, 2005

By P. Rudy

I do not want to repeat what all the other reviews have said. This is a quality compressor. In this day and age of plastic junk, I am surprised some of the reviews complained about wieght. The weight comes from steel, not plastic parts. The tanks are heavy steel as is the roll cage around the entire mechanism. The handle is in the center, so carrying it is well balanced.

The compressor is just as quiet as others report. I have it in the corner of my workshop about 10 from me. The start up instructions are easy and you are up and running in 20 minutes.

Why did I get this compressor? In sum, (1) I wanted a GOOD quality tool that was not Chineese junk, (2) I wanted at least 4 cfm for tools and (2) I did not want to spend a fortune. There seems to be several classes or levels of compressor in the lower price range. Unless you are getting a specialized mini-compressor just for a small brad gun, the $125-175 compressors are mostly junk: loud and rough. This Makita is in the next step up, with compressors in the $225 to 325 range. There are some Dewalt Emglo and others I looked at in this range. Most of this second tier are either made for just for job sites or are just bigger cheaply made compressors.

I chose the Makita over the Dewalt for one reason: quiet. The Dewalt is an excellent compressor, but you cannot use it next to you in an exclosed shop -- its too loud.

So, I wanted a quality tool and one that could live in the shop next to me. The Makita does both in spades. It is a very well made little compressor. The fit and finish is great. It has a dual personality: it works and looks great in the corner of the shop AND is perfect for taking to a job site or the back yard. Best of both worlds.

The compressor seems to live up to its specs.... I have easily run 3/8 and 1/2 inch impact wrenches, a brad gun and a finish nail gun, along with blow guns, etc. When I went to use a Snap-On 7200 3/8" air ratchet, the performance was just adequate. Then I read the spec for the ratchet and it calls for 4.5 cfm. The Makita is rated at 4.2. SO, you do have to watch the cfm ratings on tools: I am sure a 8 cfm jitterbug sander will not work. But then again, that is not the type of tool I wanted this for.

I have not owned a compressor is many years. I looked long and hard for the best of all worlds: quality, size, price, and cfm. As an advanced and serious home workshop dude, this review is not written for the pros. But for a serious homeowner that appreciates quality tools and needs a general purpose compressor, I believe I found the perfect compressor.

Lastly, no shop came close to Amazon on total price, in large part due to the free shipping. Read more ›

65 of 66 people found the following review helpful

5.0 out of 5 stars Perfect compressor - quiet & powerful September 19, 2005

By Home improvement enthusiast

I needed a compressor to put up a fence, install mouldings and refinish my basement. After a TON of research, I settled on this Makita. I am very pleased. It's quiet, very well built and easy to use. So far I've run a framing nailer and brad nailer with no problems.

I've read other reviews that speak to the weight of this unit. Well, it's a compressor and they ARE heavy. That's just how it is. Especially a high-quality compressor like this one. It's not a tinny piece of junk and there's only plastic on it where it makes total sense - no where else. Makita also puts a NICE molded rubber handle on it that doesn't shift or move one bit. The thing's built like a tank and looks great. I have yet to trip a 15-Amp breaker with it.

Additional comments:

The finned discharge tubing on this thing is fantastic - if you've never had your hand seared like a steak after touching discharge tubing on a compressor, you haven't truly felt pain. I've brushed the tubing with the motor running on this one (accidentaly) and where my hand normally would have STUCK, it was only warm. Very nice touch.

The tanks fill quickly enough, and the gauges are really nice quality. The pressure regulator is pretty easy to adjust once you get the hang of it.

Again, the noise level is excellent. I can use the compressor in my basement shop and can barely hear it running on the main level. I can have a pretty much normal conversation with it running 10 feet away in the same room.

If you're looking for a high-quality, oil-lube (don't know why anyone would go for a non-oil unit) compressor that will last for years, look no further.