JET 321373 BD-920N 9-Inch Swing-by-20-Inch between Centers 3/4-Horsepower Benchtop Lathe, 115-Volt 1-Phase

Other products by Jet

Product Description

From the Manufacturer
BD-920N JET 9" x 20" belt drive bench lathe. Shown with optional stand.

Product Description
27 longitudinal feeds from 0.005 to 0.011in. Spindle is mounted in tapered roller bearings and has MT-#3 taper with 1 1/2in. x 8 TPI spindle nose. Cross slide travel of 5in. Tailstock adjusts for taper cuts. Lathe has hardened and ground bedways, 7in. 4-jaw and 4in. 3-jaw chucks, faceplate, 4-way tool post, quick change gear box, threading dial and tool kit. Single phase motor.

Product Details

• Product Dimensions: 38 x 20 x 45 inches
• Shipping Weight: 239 pounds (View shipping rates and policies)
• Shipping: This item can only be shipped to the 48 contiguous states. We regret it cannot be shipped to APO/FPO, Hawaii, Alaska, or Puerto Rico.
• ASIN: B00004T9KY
• Item model number: 321373
• Average Customer Review: 3.3 out of 5 stars See all reviews (6 customer reviews)
• Amazon.com Sales Rank: #87,855 in Home Improvement (See Bestsellers in Home Improvement)

  Popular in these categories: (What's this?)

  #3 in	Home Improvement > Power Tools > Lathes > Metal Lathes
  #15 in	Home Improvement > Power Tools > Lathes > Benchtop Lathes

• Discontinued by manufacturer: Yes

Customer Reviews

Most Helpful Customer Reviews

2 of 2 people found the following review helpful:

4.0 out of 5 stars Great Machine for the Money, April 11, 2008

By	Mark T. Shipley (Thousand Oaks, CA United States) - See all my reviews (REAL NAME)

I was looking for a benchtop lathe with a little more grunt and capability than the smaller, hobby-type machines, and without spending a ton of money. The lathe arrived well crated and covered with preservative. Plan on using up a roll of paper towels getting this stuff off. Once mounted on my workbench, I checked the spindle for runout with a coax indicator and also checked the tailstock alignment. Both were on the money. I obtained a live center, drill chuck, and a set of tool holders locally, and was off and running. First project was a steering tube for an outboard motor, that required a 12" length of aluminum stock to be turned to 7/8" OD and a 14-TPI thread cut. Both operations went extrememly well. Vibration is very low and this machine is solid.

Some gripes: When cutting threads coarser than 14 TPI, the end gearing arrangement prevents the access cover from being closed. This I see as a potential safety issue. I would like to see a power cross feed added, even if it added to the cost of the machine. Finally, I would like to see the inside of the tailstock taper keyed for the drill-chuck arbor.

All said, this is a lot of lathe for the money. I see from other reviews that some people aren't happy, but my experience has been positive so far. I've done this stuff for a living on a $20,000 toolroom lathe and this little JET does many things just as well. It is a small machine with limited power, but should serve most home machinists very well when used within its limitations.

1 of 1 people found the following review helpful:

5.0 out of 5 stars Best bang for the buck!, October 19, 2006

By	Eric R. Kessler (Reading, Pa) - See all my reviews (REAL NAME)

I have for about 6 months now and used it many times and found it to be well built and easy to use. No problems with it so far and very happy with it! What a great machine! I got mine on sale here at Amazon for 992.68 shipped the door. Just watch for their tool sales!

2.0 out of 5 stars Jet 9x20 metal Lathe, April 6, 2008

By	Lee R. Nichols "crankeyguy" (K town tenn) - See all my reviews (REAL NAME)

I got mine really fast from Amazon at a great price. I found the lathe to be in pretty good shape. I would advise that after you get one that you disassemble the headstock and clean all the dirt and grime that you cannot see, and clean a replace the grease with good clean grease. Found the tool post mount needed to be upgraded to an 4 bolt available at mini lathe distributors. Be sure to check the alignment. I had to remove the headstock and clean it, then metal shim it .003 of an inch all around to get center to center alignment. Face alignment was great. I found that threading was useless and a DC motor needed to slow it down so you can use the threading capabilities. Mine said it had a clutch, but I have yet to find anything but a useless timing idler pulley that I think the belts could or should be run from so it would be useful. With a little upgrades, I think this will make a fine machine for the money. I think the assemblers of this machine should be fired. If I would have ran it like it was, it would have eaten the bearing fast in headstock. Chinese assemblers! Wash Your Hands! clean up your products before assembling them! Take more pride in you work!!