Racor PBH-1R Ceiling-Mounted Bike Lift

by Racor

Product Description

Amazon.com Product Description

The RacorPro PBH-1R Ceiling-Mounted Bike Lift allows you to take advantage of unused ceiling space to store your bike. Installation takes only a matter of minutes, and with its ingenious pulley system, raising and lowering your bike couldn't be easier. The lift lets you free up precious storage space on the floor, all while keeping your bike stored away safely until you're ready to ride.

The RacorPro PBH-1R Ceiling-Mounted Bike Lift: Installs easily in just minutes. Employs solid-steel construction for exception durability. Makes it simple to raise and lower your bike. Frees up floor space in your home.

Create more floor space in your home by getting your bike off the ground. View larger.

The RacorPro PHL-1R takes only minutes to install.

Easy-to-Install Pulley System Frees up Floor Space
The PBH-1R uses a pulley system that makes it easy to raise and lower bikes weighing up to 50 pounds. The system can be installed on ceilings as high as 14 feet, and the unique rope locking system ensures that the rope stays locked in place when not in use. Storing your bike off the floor not only protects your bike from damage, but it frees up valuable floor space, helping to keep your space tidy and better organized.

Installing the Racor PBH-1R is a breeze, and you can have it completed within a matter of minutes. The only tools necessary for installation are a Phillips head screwdriver, a drill with a 1/8" bit, a tape measure, and a stud finder (for ceilings with drywall). The easy-to-follow instructions will have your Ceiling-Mounted Bike Lift ready to go in just five easy steps.

Solid-Steel Construction for Durability
The PBH-1R is built to last. All of its included hardware is constructed from solid steel for maximum durability and toughness. The locking mechanism, pulleys, rope cleat, and lift mechanism offer smooth performance for years to come. The included 48-foot lift rope is also extremely durable, and it provides plenty of excess length for ceilings up to 14-feet high.

Easy Raising and Lowering with Minimal Effort
The PBH-1R makes it a breeze to raise and lower your bike from its ceiling-mounted position. The pulley system handles the brunt of the force, so it requires very little effort on your part. Simply hook the bike handlebar and seat to the included hooks and pull the lift rope to raise the bike to its ceiling-mounted storage position. With each pull, the locking mechanism locks into place to eliminate accidental drops. Store the excess rope on the included rope cleat to keep it nice and tidy.

The RacorPro PBH-1R Ceiling-Mount Bike Lift measures 10.24 x 5.12 x 3.5 inches (packaged) and weighs just 3.64 pounds (packaged). All included components feature a black finish.

What's in the Box
Two lift assemblies, two hook pulleys (one with locking mechanism), 48-foot rope, one rope cleat, 10 two-inch wood screws.

Product Description

It's a terrific way to use unused space with ease and safety. Unique rope locking mechanism prevents accidental release. Ingenious design lightens the load for easy lifting. For use on ceilings up to 14' load capacity 50 lb. Solid steel construction with

See all Product Description

Product Details

Manual [PDF]

• Item Weight: 3.6 pounds
• Shipping Weight: 3.1 pounds (View shipping rates and policies)
• Shipping: This item is also available for shipping to select countries outside the U.S.
• ASIN: B00006JBL3
• California residents: Click here for Proposition 65 warning.
• Item model number: PBH-1R
• Average Customer Review: 4.4 out of 5 stars  See all reviews (264 customer reviews)
• Amazon Bestsellers Rank: #259 in Home Improvement (See Top 100 in Home Improvement)

  #20 in

  Home Improvement > Storage & Home Organization

Customer Reviews

Most Helpful Customer Reviews

117 of 118 people found the following review helpful:

5.0 out of 5 stars Easy to install and easy to use, August 29, 2006

By	skst (Arlington Hts., IL USA) - See all my reviews

This review is from: Racor PBH-1R Ceiling-Mounted Bike Lift (Tools & Hardware)

I received two of these bike lifts as gifts. I installed them to replace my old "hooks-in-the-ceiling" method of hanging bicycles over my car. I had to take care to measure the height of the bicycle (adding a few inches for the pulleys) to ensure they cleared the car. I also measured the length of the bicycle to ensure it wouldn't be in the way of people walking around the car. Finally, I measured between the handlebars and seat so the pulleys were properly spaced. But once that was done, installation was a simple matter of drilling three pilot holes per pulley in a joist and screwing them in.

Although the instructions say to tie a stop knot in the rope and thread it through the pulleys and hooks before installation, it's easier not to do that until after you've installed the pulleys. (I did tie a knot in the rope and run it through the hole before I installed the first pulley, but that that turned out not to be necessary because there's enough clearance to push the rope through afterwards.)

Finally, I installed the cleats low enough to reach but high enough so people don't have to duck under the rope.

Like some of the other reviewers, one of my ropes was frayed. (The other one was fine.) I wrote an e-mail to Racor and a vice-president responded almost immediately. I received a replacement rope two days later. Awesome!

Conclusion: These lifts work very well, are easy to install, are reasonably priced, and are backed by excellent customer service.

74 of 77 people found the following review helpful:

3.0 out of 5 stars Great concept, poor implementation, December 25, 2005

By	T.K. "Tom" (Western Maryland) - See all my reviews

This review is from: Racor PBH-1R Ceiling-Mounted Bike Lift (Tools & Hardware)

This is a very useful, nifty little device. Too bad the manufacturer won't commit
to making it a quality product. It does sell for a cheap enough price that you can afford to swap in a high quality rope and some decent screws. To fit the brackets snuggly over a 2x joist, you'd need to shim it on either side. It also should be shimmed on the underside, because the nuts holding the pulleys prevent the brackets from fitting flush to the joist bottom. Without the bottom shims, stress is not distributed evenly. The whole design, in addition to the crappy screws, invites unsafe installations unless you make some corrections.

76 of 81 people found the following review helpful:

3.0 out of 5 stars Be prepared to replace the rope., July 12, 2006

By	V. Beck (Galveston, TX) - See all my reviews (REAL NAME)

Amazon Verified Purchase

This review is from: Racor PBH-1R Ceiling-Mounted Bike Lift (Tools & Hardware)

This product works and is relatively easy to install. However, the supplied rope is garbage. It has many frays right out of the box, and, upon first use, looks like it could break at any time. It is some cheapo cotton worthlessness. Would you feel comfortable with that cheap stuff suspending a bike over your new Lexus? It's too bad these folks don't have the foresight to spend a few extra few cents and supply a real rope instead of making customers go out to buy one and then having to reinstall it. Shame on them.