|
|
56 of 57 people found the following review helpful:
5.0 out of 5 stars
The pros and cons of robomowing, June 2, 2003
Before using the robomower, I had to lay out a perimeter wire for each of the areas I wanted mowed. In my case, I divided my lawn into three sections, the back yard, the front yard to the left of my driveway, and the front yard to the right of the driveway. The wire is an electronic barrier, not a physical one. It's flush with the ground, and held in place by plastic tent pegs. The tent pegs and the wire come with the mower.Besides the outside edge, I also used the wire to mark off obstacles. I have some mulched covered areas with plants, and some of the trees have mulch around them that's too steep for the mower, and which doesn't need to be mowed anyway. For islands, I ran a wire from the perimeter, circled the obstacle, and then ran a wire back parallel to the incoming wire. Two wires side by side cancel each other out, and the mower ignores it. Not all obstacles require wire. I did not have to mark several of the trees in the back yard. The mower has bumpers around the outside edge, and if the obstacle is 6" tall and reasonably resilient, that's sufficient. It doesn't bump into things very hard, but a soft plant stem isn't going to offer enough resistance. Laying down the wire was a lot of work. I ended up pegging down about 1200 feet of wire to enclose a 1/2 acre lawn, which probably took me about 3 hours total. Objectively this is more work than mowing the lawn a couple of times would have been, but it was more interesting than mowing. There's a little mental challenge in trying to place a reasonable curve around an obstacle or an edge. The mower comes with a signal generator which I attach to the wire for the zone I'm going to mow. After I release the mower into the zone, the mower seeks out an edge and then follows it for roughly one complete circuit. The mower then begins criss-crossing the lawn, stopping each time it either senses the wire or bumps into an obstacle. It then turns slightly and reverses direction, mowing a strip roughly parallel to the first. Eventually it decides to take a 90 degree turn, to being mowing a set of strips in an alternate direction. The mower is really slow, particularly since it misses large patches on the initial pass. It makes up for this by making several passes over the lawn. For each zone, I've let it run for the maximum time of 2 1/2 hours, and despite those patches it missed initially it mowed everything by the time it was done. I had no complaints about the result in the back yard. To my mind, it doesn't matter how long it takes, since my time investment is a couple of minutes to drive it over to the lawn, and then a press of the "go" button. The mower is very, very quiet. It has three 7" blades, and it's battery powered, so I can hardly hear it from inside the house. The sound is kind of funky, like a turbine or something, since the three blades produce odd harmonics. My only real problem came up with the left front yard, which has an unusual feature. It's a large depression that was intended as a catch basin for water runoff, so that rain goes back into the water table instead of the sewer. Some of the angles are just plain too steep for the mower. To be fair, they'd be too steep for any mower - the robomower is short and squat, and very stable, but a 40 degree angle slope is likely to tip any mower over. Some of the slopes are gentle enough for the mower, so my initial attempt was to mark off only the steep slopes. This resulted in a cup-shaped obstacle, which actually had "lips" and a relatively narrow opening. Unfortunately, while the mower handled the slopes I left open well enough, it spent way too much bouncing around inside the depression. It never quite figured its way around to the other side, which it did quite handly with more convex obstacles I marked in other zones. As a result, I marked the entire thing off as an obstacle, and made a tiny zone inside the depression. Alternately, I could have mowed this manually. Driving the mower manually is sort of like playing a videogame. There's a controller on a coiled leash that has a direction pad. I push the direction pad, and the mower goes in that direction. The turning radius is zero, since the drive wheels can spin in opposite directions if you ask for a tight turn. It works, but it's really kind of awkward, particularly if I have to make several turns. I do have to drive it manually with the controller to and from the lawn. The mower is heavy, mainly because it has a big, sealed lead-acid battery. It's roughly the size and weight of a car battery. It lifts out easily so you can do things like tilt the mower on its side to clean the blades. The mower takes a long time to charge. The instructions say 24 hours, but it's more like 30 in my experience. This means that as a practical matter, I can only mow once every two days. This isn't really a drawback, since each zone probably only needs to be mowed every two weeks, though it was annoying when I was first starting and was impatient to play with the new toy. They do sell an external fast charger which takes 6 hours to charge the battery. They also sell extra batteries, again for convenience. Overall, I'm happy with my gadget purchase. It's quiet, it does the job, and it requires almost no effort on my part to mow the lawn, now that I've invested the labor of placing the wires.
|