Bench Dog 10-010 Crown-Cut Crown Molding Cutting Jig

Other products by Bench Dog

Product Description

Amazon.com Review

There’s no denying that nearly everyone loves crown molding, but cutting the molding is no picnic—even for some pros. That’s because crown molding gets installed at an angle against the wall and ceiling, and precise cuts are required to obtain tight-fitting corner joints. Complicating the situation is the fact that crown molding is expensive; it only takes two or three miscuts to blow your budget. But don’t despair you can end the trepidation and frustration with the Bench Dog 10-010 Crown-Cut Jig. This surprisingly simple device provides a quick, foolproof way to cut crown molding, even for novice do-it-yourselfers.

Crown-Cut is designed to work with any 10-inch or larger power miter saw, and it’ll accommodate crown moldings up to 6 inches wide. The jig is made of Baltic birch plywood and it plastic stops and steel tabs that adjust to match the molding’s height and distance it projects from the wall.

To use the jig, simply set it onto the saw table and adjust it to match the molding size. Then place the molding into the jig and it’ll automatically be held at the proper wall angle. Set the saw blade to 45 degrees, and make the cut. This method is much easier than holding the molding flat on the table and setting the saw for a compound angle cut, which requires figuring out both bevel and miter angles. -- Joseph Truini

Product Description

Crown Molding Cutting Jig - CROWN MOLDING CUTTING JIG. Produces perfect fitting miters every time. Crown stop quickly adjusts to lock molding. Fits all 10" & larger miter saws

See all Product Description

Product Details

• Product Dimensions: 15 x 5.9 x 3.9 inches
• Shipping Weight: 2 pounds
• Shipping: Currently, item can be shipped only within the U.S.
• ASIN: B0006FKGGC
• Item model number: 10-010
• Average Customer Review: 4.2 out of 5 stars  See all reviews (24 customer reviews)
• Amazon.com Sales Rank: #27,729 in Home Improvement (See Bestsellers in Home Improvement)

  Popular in these categories: (What's this?)

  #9 in	Home Improvement > Power Tool Accessories > Extensions & Stops
  #46 in	Home Improvement > Hand Tools > Measuring & Layout Tools > Marking Tools
  #98 in	Home Improvement > Power Tool Accessories > Saw Accessories > Miter Saw Accessories

Customer Reviews

Most Helpful Customer Reviews

31 of 32 people found the following review helpful:

3.0 out of 5 stars I've Used One Of These,,,,,,, September 18, 2005

By	Tom in KY "Square Eye for the Tool Guy" (Western KY) - See all my reviews

This is a nice jig for just about any miter saw. It's made of materials that have been proven durable over time. It's fully adjustable, both for width of crown from wall and for hight from ceiling to bottom of crown. The width adjustment is a plastic crown stop with 2 solidly anchoring screws attached through slots in the bottom of the jig. The hight adjustment is steel extension tabs that slide up from the back fence. This is a fine set-up for dual compound saws, BUT, the motor on a standard compound (or non-compound) mitersaw will contact the back fence when you use the jig on the right side of the blade. This is not a problem if you can make all of your miter/coping cuts on the left side of the blade. The upside down method of cutting crown can get confusing if you're mitering in both directions anyway.

If you would prefer to use the full capacity of your saw though,,, buy the crown stops that the manufacturer of your saw offers. The manufacturer of your saw probably offers crown stops that let you use the full capacity of your saw. The Bench Dog takes away 3/4 inch wide and 3/4 inch high, just like a homemade version would. On a 10 inch miter saw this can be a problem when cutting wide crown molding. Although, you can make a home made version that leaves the capacity at original specification.

ONE LAST THOUGHT, FASTEN THIS DOWN TO YOUR SAW!!!!! Keep your fingers a little while longer and make your cuts more accurate. Leaving this jig loose could lead to cumulative error. Sawdust can get under it, the angle could be affected by the way you have the material supported, etc. The fence is probably the best place to attach, just put a couple of short screws right through the back of the fence and into the jig. Then if the material is a little off of the jig on one side or the other, you'll be able to see it. And with the jig fastened down, the chance of the jig sliding around and losing your mark is eliminated. This is a nicely crafted jig and will give you very dependable service if you treat it well.

13 of 13 people found the following review helpful:

5.0 out of 5 stars Crown Molding Jig you Need, July 19, 2005

By	N. luczak (New Jersey) - See all my reviews (REAL NAME)

If you are a novice attempting to cut crown molding, this jig is for you. The Bench-Dog Crown Cut Molding jig does a GREAT job explaining the whole "cutting opposite" technique used to cut crown molding. The best part of the jig is the detailed pictures on the jig itself. There is no need for instructions, although they are very helpful as well. One can make a similar jig on their miter saw using wood and some glue (I tried it, I couldn't get it right), however this jig made it very simple and fast to cut crown molding. A must have for the do-it-yourselfer. Word advice though, before you cut your expensive crown molding experiment with an extra piece (or cheap piece) of crown molding to get the hang of it first.

14 of 15 people found the following review helpful:

5.0 out of 5 stars Crown-Cut Fast, Easy with Great Results, February 27, 2005

By	T. Lewis - See all my reviews (REAL NAME)

I've used Crown Cut to cut crown molding for 12 rooms and it takes all of the confusion and guess work out of making inside and outside corner cuts. No need to set up special benches, crown stops, setting the bevel angle and trying to figure out the upside down and backward cutting. You don't even need a compound miter saw. There are only 2 steps to cut perfect inside right/left and outside right/left corners. The best part is, the steps are listed right on the Crown Cut jig. For a Do-It-Yourselfer, it will make your crown project less confusing and frustrating. Even my wife was amazed how fast the rooms were done and how much better the crown made the rooms look. To summarize, no headaches, fast great looking results and you will be proud to say I did it myself.