You get MORE for your money with this one!
I bought this mount after reading the reviews and was a little edgy about it because of the "one star" review i read that said it might just drop from the ceiling...Well before i hung my projector from it I ACTUALLY GRABBED ONTO IT AND HUNG WITH THE FULL 140LBS OF MY BODY WEIGHT AND IT SLIPPED ABOUT 1/4" AND THEN CAUGHT. I noticed that if you turn the sliding height...
Don't buy this
You get what you pay for, and sometimes not even that!! I was replacing my Atdec flush mount, because I needed to lower the projector about 12 inches, and man is there a difference in engineering! First off the lateral twist adjustment is worthless to unusable. There are 2 inaccessible screws to make this adjustment or you can rotate the ceiling mount plate about 15...
This review is from: VideoSecu Universal LCD/DLP Projector Ceiling Mount Bracket White Fits both flat or Vaulted ceiling PJ2W 1CA (Office Product)
I bought this mount after reading the reviews and was a little edgy about it because of the "one star" review i read that said it might just drop from the ceiling...Well before i hung my projector from it I ACTUALLY GRABBED ONTO IT AND HUNG WITH THE FULL 140LBS OF MY BODY WEIGHT AND IT SLIPPED ABOUT 1/4" AND THEN CAUGHT. I noticed that if you turn the sliding height adjustment bar upside down it will slip off SO MAKE SURE YOU PUT THAT BAR ON THE RIGHT WAY (try it both ways, the right one will be obvious) If you install it correctly you REALLY CANT BEAT THIS FOR THE MONEY. It is a must that you be somewhat mechanically inclined..if your unsure, have a friend on hand for second opinions and to help you hold everything steady. Once its up its easy to make adjustments and it looks sweet!
Help other customers find the most helpful reviews
This review is from: VideoSecu Universal LCD/DLP Projector Ceiling Mount Bracket White Fits both flat or Vaulted ceiling PJ2W 1CA (Office Product)
This did the job that was needed!! I used this mount for an Inforcus projector for our theatre room. First off, prior reviews made me suspect of buying this because they stated flimsy quality, mount, hardware, etc. I hooked this too a stud in the ceiling and it easliy held my wife a couple feet from the floor!!!!!!! The instructions could be a little bit better, but its pretty much common sense. Pitch and yaw angles are minimal, but will get the job done to make sure your have a straight picture. I even hooked this mount to an Optoma just to see if it would fit and no suprises it did with ease. If you contemplating this mount, I would say get it!! it is surely worth the cheap price and the delivery time was amazing as well!
Help other customers find the most helpful reviews
This review is from: VideoSecu Universal LCD/DLP Projector Ceiling Mount Bracket White Fits both flat or Vaulted ceiling PJ2W 1CA (Office Product)
This product worked great for me. (used with a Benq W500 projector) It was helpful how the product description had the maximum point-to-point length of your projector that this mount would be compatible with. So I knew it would fit before I bought it. There were no actual instructions, but it was easy enough to figure out. Just make sure you do it while your cat is out shopping or mowing the lawn; mine enjoyed depositing the little pieces of hardware in hiding places. For the negative, I don't trust the extension bar; the whole rig is held by one bolt. Make sure you add a safety rope/wire in case it comes loose. (of course, you don't have to use the extension)
Help other customers find the most helpful reviews
This review is from: VideoSecu Universal LCD/DLP Projector Ceiling Mount Bracket White Fits both flat or Vaulted ceiling PJ2W 1CA (Office Product)
I bought this mount to be used in a church, Also had a projector that needed a special mount for very close 4 hole mount. This mount was just what the Dr. ordered. Mounts to normal studs just fine, if you turn it the right way... Fixing to order a second one for a rear mount projector to our church.
Help other customers find the most helpful reviews
This review is from: VideoSecu Universal LCD/DLP Projector Ceiling Mount Bracket White Fits both flat or Vaulted ceiling PJ2W 1CA (Office Product)
The shaft length is adjustable.
Lots of adjustment screws to fine tune position of the projector after it has been screwed to the posts.
Only gotcha is that it comes with 4 mounting legs, but only three 3" extenders. Using just the 3 that were provided, I could not mount on the four posts of my projector, even though the max distance between any two posts on my projector is 10.5 (within the specs for this kit).
However, once I contacted the seller, they were quick to mail me the extra extender. All set now.
Help other customers find the most helpful reviews
This review is from: VideoSecu Universal LCD/DLP Projector Ceiling Mount Bracket White Fits both flat or Vaulted ceiling PJ2W 1CA (Office Product)
I bought this for my HD-65 and besides having to mess with arms a little bit to get it to actually fit this tiny projector I had to use just 3 of the little arms on it. Just a heads up for HD-65 owners. It works great though. It's solid sturdy and blends in with my white ceiling.. The best I've found for the price
Help other customers find the most helpful reviews
This review is from: VideoSecu Universal LCD/DLP Projector Ceiling Mount Bracket White Fits both flat or Vaulted ceiling PJ2W 1CA (Office Product)
Pros: This mounting bracket was very easy to install on our drop ceiling. And is also very user friendly to adjust the swivel to go up or down, left or right for an accurate screen on our wall
Con: Did not have screws that fit in our Epson projector. I had to take our projector to a hardware store and make sure the screws would fit.
Other than not having the supplied screws this bracket is very nice to have.
Help other customers find the most helpful reviews
This review is from: VideoSecu Universal LCD/DLP Projector Ceiling Mount Bracket White Fits both flat or Vaulted ceiling PJ2W 1CA (Office Product)
You get what you pay for, and sometimes not even that!! I was replacing my Atdec flush mount, because I needed to lower the projector about 12 inches, and man is there a difference in engineering! First off the lateral twist adjustment is worthless to unusable. There are 2 inaccessible screws to make this adjustment or you can rotate the ceiling mount plate about 15 degrees. The Ceiling mount is worthless for mounting in a single 2x8 ceiling stud because they designed it with 4 holes that are stupidly 3 inches apart. This wouldn't even work for a double stud! I mounted mine diagonal using only 2 of the holes. There are 4 machine screws to hold the extension to the ceiling plate and four more to hold the projector mount to the extension but only ONE LOUSY SCREW for a friction plate that keeps the whole thing from crashing down!!!! In fact while I was adjusting everything (without the projector thank God), a tightened a screw that changed the shape of the extension and the friction set screw popped loose and the whole assembly hit the floor leaving me wondering how I was going to make sure that didn't happen with my projector. I decided to drill a hole through the two parts of the extension and put a screw through it to prevent the two parts from pulling apart. - Believe it or not there is more but you get the idea.
Help other customers find the most helpful reviews
(
Saving...
