- "Huge" Color Touch Screen: with no threshold,which is more friendly and easier operation
- Laser Engraving: extremely good at engraving objects such as wood, plastic, leather, paper and even cutting thin materials like plastic
- Filament detection: if the filament spool runs out during printing, the machine automatically pauses for you to load in a fresh spool, very useful for big volume object printing
- WIFI Control: the included networking feature permits you to control the print via a phone or PC
- Copy printing: dual extruders can print two same objects at one time, cut your printing time at least in HALF
BIBO 3D Printer Metal Frame Dual Extruder Laser Engraving WIFI Touch Screen Cut Printing Time In Half Filament Detect Demountable Glass Bed
|You Save:||$130.00 (13%)|
Customers who viewed this item also viewed
BIBO2 touch laser is the most featured printer. Now order the BIBO2 touch laser, we will send you the WIFI module (USD20, pre-installed) and laser engraving module (USD22) as the gifts. It is, of course, a 3D printer. But it’s also a laser engraver, too, permitting the ability to engrave on wood or even cut paper and cardboard. Not every 3D printer has such an extra feature, and those that do often cost far more than this machine.
1=3? Yes, 1 × BIBO2 touch laser =1 × laser engraving machine+2 × 3D printers(copy printing can print two same objects which are less than 33mm in width at the same time)
Extruder Number: 2
Frame: 6mm thick aluminum composite panel
Full-color Touch Screen: Yes
Laser Engraving: Yes
WIFI Control: Yes
Copy Printing: Yes
Continue Printing After Power Cut: Yes
Filament Run-out Detection: Yes
Removable Heated Bed: Yes (already leveled, usually no need to level it again)
Number of Fan to Cool Plastic extruded: 2
Printing Mode:USB connect PC or SD card or U disk
Weight: 35.3 pounds
Build Size :8.4*7.3*6.3(in) / 214*186*160（mm）
Printing Layer Resolution: 0.05-0.3mm
Max. Nozzle Temp.:270℃
Recommended Software: Repetier-Host, Cura, Simplify3D
Compatibility: Windows, Mac, Linux
Filament Type:ABS, PLA, Dissolvable filament (PVA, HIPS), Flexible filament (TPU)
Filament Diameter 1.75mm
SHOPPING NOW! You can get these gifts:
1 x laser engraving module
1 x WIFI module (pre-installed)
1 x acrylic cover kit
2.2 LBS (1.0KG)PLA filament
1 x SD card
1 x glass bed
1 x glue stick
1 x USB cable
Top customer reviews
Before getting this printer, I had never owned a 3d printer (though I do have experience with modeling). Instructions were easy enough to understand with expected translation errors, but I had no issues getting this put together and printing the same day it arrived. Just yesterday I was able to try out the copy printing function and it's as simple as inserting a few lines of code into your .gcode files. This will definitely be a time saver for future print jobs.
I have yet to get to the laser attachment, but I will try to update with my experience when I do.
Packaging:The item came extremely quickly with all parts in functioning order, no issues with bed or z-axis being misaligned as some others stated, I think their packaging has improved since the early shipments. There were, however some noticeable cracks in the frame as well as a dent on the front corner which was a bit of a bummer.
User Interface: The company provides all the software to get right to printing, all of your settings in Cura/Repetier are just a simple import function away (though you will need to modify some settings depending on the filament you use). The touch screen makes the printer easy to control, you can modify temperature settings as well as fan settings during the print job. I have experienced the unresponsive screen / heating elements at times after performing a print and moving on to another, but a simple shut down and restart resolves this issue.
Bed Allignment: I had to modify the plastic washers that come with the printer to get the bed to properly allign at first (some light sanding, took them down about halfway). Before modification the bed would not adjust low enough for the nozzles. I usually relevel the bed after every major print (very easy procedure), but I can get away with leaving it the same between smaller prints.
Installation: Instructions / videos were easy to follow along with, basically you will need to install the; glass bed, filament holders, filament guides, printing nozzle / hotends / extruder, the front door, and the top lid. Some issues I ran into during construction was one of the cooling fans was pre-installed at the wrong angle (horizontal instead of vertical) but it was pretty obvious to fix since the hotend wouldn't fit in it's hole with it installed that way (just a simple re-angling of the nuts). The holes for the filament guide, on the guide itself, had some residue that prevented the screws from going in, easy enough to use an exact-o and scrape it to the proper opening size. Other than that, everything went together as intended.
Final thoughts: If you are looking for a low maintenance printer to get right to printing, this is the printer for you. It's packed with features at a reasonable price. I would rather focus on the design / printing aspect of this hobby rather than the tuning of the printer itself. I would definitely recommend this product
Although this printer isn't for beginners, the manual is thorough and easy to read.
This printer can use a wide variety of filaments.
If you are a prosumer or merely a consumer that wants better than hobby grade, this is the printer for you.
Customer support is great.
I purchased the BIBO printer with the multiple laser engraver because that just seemed like it would be fun to play with.
BIBO was packaged extremely well, superfast shipping…I ordered it…a few days later it arrived
What I love so far about this printer is its well-made, there are videos on a Memory Card/SD Card include to help put together the last 10% of putting together the printer. Remember although technical, this is all new to me. I found this easy to use and the instructions fantastic. They also use whatsapp on android/iPhone if you need to ask questions…and I used it on a question I had and I was responded to in less than 15 minutes.
I then made an account over at thinginverse.com to I could download the .stl files to put on the memory card and start printing! Below is one of the prints…it speaks for itself, I could not be happier. I plan on trying the laser engraver and printing out some family photos and loved pets on wood as soon as I conquer the printing requests I have received from family 😊.
I don’t typically spend time on reviews, but when I receive a good product, it’s worth sharing to you all. I hope this helps your buying decision.
I have attached two photos, one is of the actual object that i downloaded, the other is the object being built by BIBO..around 50% complete. Simply amazing.
Most recent customer reviews
I received a reply within the 1/2 hour!Read more