Other Sellers on Amazon
+ Free Shipping
+ $5.20 shipping
+ $6.04 shipping
Crosman Williams® Peep Sight.
|Price:||$44.95 & FREE Shipping on orders over $49. Details|
Fulfillment by Amazon (FBA) is a service we offer sellers that lets them store their products in Amazon's fulfillment centers, and we directly pack, ship, and provide customer service for these products. Something we hope you'll especially enjoy: FBA items qualify for FREE Shipping and .
If you're a seller, Fulfillment by Amazon can help you increase your sales. We invite you to learn more about Fulfillment by Amazon .
- Enter your model number to make sure this fits.
- For current Benjamin and Sheridan rifles
- Factory drilled and tapped for easy installation
- Peep sight
- Receiver Mounted. Factory Drilled and Tapped for Easy Installation.
Frequently Bought Together
Customers Who Bought This Item Also Bought
Top Customer Reviews
Funciona bien pero primero hay que limar el fondo pues queda muy alta para usarse con rifles benjamin sheridam 392/397. Si se deja como viene agrupa muy arriba.
No, it is definitely NOT "Okay" but I had to give it 3 stars to get published.
Something here simply does not compute. I ordered this sight on August third, within days of taking delivery of my Crosman Benjamin 392. It did not arrive until today, 11/22. and only after I had a few stern words in reply to the e-mail from the seller a few days ago asking me how I liked it.
Well, sure enough, the pre-tapped holes on the right side of my 392 match up perfectly with the holes in the sight mounting, if you turn it upside down so that the aperture is backwards.
In order to mount it , I would have to clamp that part of the sight into a vice and take a grinder to it. I would have to grind off 15/32 of an inch on the two protusions, one beneath each of the two screw holes on the ends.
Some reviewers say they have no problems. Others cite this same problem - having to grind it to make it fit.
There is not enough room on the rifle for the holes tapped into the rifle to be too low.
The only possible answer that comes to mind is that there are different models of this sight and some of us are receiving the wrong model.
The plastic "safe" mine arrived in has a label with a bar code and the words "XOOOHEUBH7 New- Crosman Williams Peep Sight." Even worse, I just found the cardborad insert that came inside of it. What they sent me was a model 5D-SH. That is listed on the back of the card as being "5D-SH - for Sheridan Blue Streak and Silver Streak Air Rifles." There are descriptions of 6 other sights in the "%D series. NOT ONE is listed as fitting a Crosman-Benjamin Model 392. God only knows how many of us have been sent the wrong damned sight!Read more ›
I purchased this sight for my brand new Benjamin 392. The sight mounted easily and everything seemed to be fine with it. However when I began sighting it in I discovered the limitations of this sight, particularly in regard to windage adjustments. I noticed immediately, that with the sight windage centered, the rifle was impacting approximately 2 inches to the left of point of aim at a distance of about 20 ft. Despite shifting the sight all the way to the right, I could not correct this problem. I suspect that the alignment of the Benjamin barrel is off...or the front sight is misaligned....or both. So...I guess this is the fault of the rifle. HOWEVER....there is little you can do to correct this. The range of adjustment for windage is so limited that you can't compensate for it. I tried using two small washers as shims underneath the sight where it mounts to the rifle, just so I could get the sight a little further to the right. That allowed me to at least get the rifle to impact to the point at which I was aiming. BUT....one of the screws is so short that I could not get it to thread into the rifle. So....I've got one screw holding the sight in place. Not good. Now I have to try to find a longer screw that has the same thread count that will actually fit into the sight itself. Not sure I'm going to be able to get that done.
The CONCEPT of this sight is fine. It's not necessarily poorly designed. There are just not enough options for getting this sight to work correctly with this rifle. And I believe that may be due to variations in quality control with the rifles themselves.Read more ›
Most Recent Customer Reviews
Nice quality all aluminum construction, mounted perfectly on my Benjamin 392, had to shorten one of the screws because it was pinching the bolt, no big deal, looks great, awesome... Read morePublished 27 days ago by Eugene Bell
Purchased for a benjamin 392. Found it impossible to screw in the elevation set screw using the supplied silver wedge shaped washer. Read morePublished 2 months ago by Amazon Customer
Works well enough. Hell, works better than the stock rear sight on the current 397. Came with the painted on Williams logo partially scraped off. Minus one for poor QC. Read morePublished 2 months ago by PKC
I recently purchased a 20 cal Sheridan/Crosman C9A, brand new in the box, but old stock as these guns are no longer made in 20 cal. Read morePublished 4 months ago by Syncro
fit like a glove. It's a different gun now. I only wish the lateral adjustment had a screw to make fine moves easier. As it is works well, though.Published 5 months ago by Paul D. Eberhardt