This is a quick install guide that I decided to write for anyone that could use some help. Specifically if you are a PC person and your significant other is a Mac user with a slooooow MacBook in need of an upgrade. I will break this review up into sections.
Note: If you are reading this to resolve slow startup into OSX after SSD install skip to section 3. of this review.
1. Preparation
2. Install
3. Finishing actions for proper operation
1. Preparation to install your new shiny SSD
1.a You will need a migration tool (I used the Sabrent kit USB 3.0 to Sata that was suggested in these review) see link http://www.amazon.com/gp/product/B00DQJME7Y/ref=oh_details_o03_s01_i01?ie=UTF8&psc=1
1.b You will need to download a trim enabler (mid 2012 macbooks only support native trim with apple brand ssd's) I recommend going to cindori.org and downloading trim enabler version 3.xx. You can do this step before or after the OS migration
1.c You cannot use the Samsung SSD migration software *don't worry Mac has its own imaging/migration utility*
1.d You will need a torq bit driver or pliers as well as a small Philips screw driver, and an anti-static wrist strap
2. Installation
2.a SSD migration set up: Attach the power to the Sabrent kit with the inline cord switch off. Attach sata power and data cable to SSD and to the Sabrent kit. Plug in usb cable to the MacBook. You should be prompted to initialize the drive, if not you can initialize in the next step.
2.b select the go menu on the OSX tool bar and open utilities.
2.c Open drive utilities. You should see your Toshiba HD with a subfolder underneath titled Mac HD; below that you should see your SSD device. Highlight the SSD and click the restore option tab in the main window of the utility screen. You will have the option to format the device using the Mac journal format. Go ahead and format your SSD to the journal format; you will also be prompted to name your device. I decided on Samsung SSD, but you can name it whatever you like.
2.d Shut down your MacBook
2.e Power on your MacBook and hold down the command + r keys simultaneously. This will start the MacBook recovery utility.
Note: Mac uses onboard utilities to clone and migrate software. The Samsung migration software will not be used.
2.f Select the drive utility. Then select the restore tab again. This time highlight the "Mac HD" device on the left hand column and ensure that the "Mac HD device" appears in the origination line. Then place cursor in the destination line and select the Samsung SSD device. At this point on your main utility screen under the restoration tab you should see the Mac HD device first and the destination drive on the second line should be your Samsung SSD. Click restore and accept yes for any formatting prompts, etc. This will begin the cloning of the installed hard drive to your new SSD. Will take anywhere from 20 minutes to much longer depending on the size of data. *160 gb's took about 30 minutes on my wifes MacBook*.
2.g Upon completion of the cloning operation you will still be at the recovery utility screen. Go ahead and select the apple icon in the left hand corner and select shutdown. Once the MacBook is off power down the inline Sabrent power cable switch and disconnect all cables to the SSD. Caution! Do not pull up on the sata cables; use a straight pulling motion as to not break the SSD connectors on the controller.
2.h Open the MacBook from the back by removing all fasteners. *orientation of the Macbook is face down with the back of the macbook facing your body* Once open disconnect the power cable; located on the left hand side middle of the MacBook (1 inch black flat connector on the motherboard). Locate the retention bracket for the hard drive and undo the two fasteners. Carefully lift the hard drive out and disconnect the unibody sata power/data rail from the hard drive.
2.i Remove Qty (4) fasteners from hard drive using torq bit or pliers. Note: these fastners have nylock elements and will initially require a good amount of break away torque to undo, so don't be afraid to put a little back into it. Once the fasteners are removed install 4 fasteners into the SSD. Hand tighten the 4 fasteners until the fastener shank with the nylock reaches the SSD mounting thru holes. Use torq bit or pliers to finish tightening the fasteners until the fastener heads are flush with the SSD mounting thru holes.
2.j Install the unibody sata rail onto the SSD and firmly seat. Place the SSD into the MacBook and re-install the retention bracket using the screwdriver. Then re-install the back cover.
3. Finishing touches
Note: initial start ups will be slow, and show no improvement over the replaced hard drive. The subsequent steps below will solve the sluggishness and slow startups.
3.a Before restarting the mackbook Hold ctrl+shift+option+power button down together. Simultaneously release these buttons and then count 10 full seconds.
3.b Power on your MacBook and wait for it to boot. *if data migration and installation were proper it will take 30 to 45 seconds to boot into OSX*
3.c. Download and/or run the Trim enabler from Cindori.org version 3.xx. You will need to left click and drag the download to the application folder. Upon completion open the application folder and click the Trim Enabler program. Trim enabler will prompt warnings for downloaded files from internet, etc, etc, and want to run a helper. Allow them all. Once the program is open it will display a small graphic user interface with a switch that says off to on. Click on the switch to turn on. Once this is done it will should prompt you to reboot your MacBook. Reboot the MacBook.
3.d *again load times for OSX should be 30 to 45 seconds* Once you are back into OSX select the go menu on the OSX toolbar then select utilities. Select the system properties to display devices; on the left hand side you should see a list of all your devices including your "Mac HD" which is your new SSD. Highlight the Mac HD and verify the following: S.M.A.R.T=verified, and T.R.I.M = Yes. They should both be verified and yes.
3.e Now to solve the slowness issue! Select the go menu from the OSX toolbar then select utilities. Locate and select startup disk. Once start up disk menu is open you should see your MAC HD device *new SSD*. Select the Mac HD device as the startup device. You should be prompted to restart. If not manually restart from the restart button shown on the start up disk utility window.
3.f You should now have a 7 to 10 second start time into OSX with your new trim enabled Samsung EVO 840 SSD.
Give MacBook over to wife and bask in the praise for getting rid of the OSX application loading circle!
| Standing screen display size | 2.5 Inches |
|---|---|
| Hard Drive | 500 GB Solid State Drive |
