DZS Elec 600W DC Booster Constant Voltage Constant Current Power Converter Module DC-DC 12V-60V 10A Adjustable Step-Up Power Supply Module CC CV Voltage Regulator Large Power Driver
- 600W Booster Constant Voltage Constant Current Power Converter Module, Input Voltage: DC 10V-60V, Output Voltage: 12-60V Continuing Adjust, The output voltage should be larger than input voltage.
- Input Current: 10A (MAX), Static Working Current: 10mA, Constant Current Range: 0.2-10A. Please enhance heat sink if output current exceed 6A.
- The booster power module adopts high thermal conductivity aluminum PCB, Working Temperature: -40 to +85 degree Celsius. Can be attached to flat metal for ehancing heat dissipation.
- Booster converter module adopts 10A/100W schottky, 50V high frequency low resistance capacitor, 27mm High Q power inductor , 2512 alloy resistor etc. much safer operation.
- Suitable for DIY voltage stabilizing power supply, vehicle power supply, high power mobile power supply, solar panel voltage stabilizer, battery/lithium battery charging, driving high power LED and so on
Frequently bought together
Customers who viewed this item also viewed
What other items do customers buy after viewing this item?
Have a question?
Find answers in product info, Q&As, reviews
Your question may be answered by sellers, manufacturers, or customers who purchased this item, who are all part of the Amazon community.
Please make sure that you are posting in the form of a question.
Please enter a question.
Module Name: 600W Booster Constant Voltage Constant Current Module
Module Type: Non-isolated booster module (BOOST)
Input Voltage: DC 10V-60V
Input Current: 10A (MAX)
Static Working Current: 10mA (The higher output voltage, the higher static current)
Output Voltage: 12-60V Continuing Adjust
Output Current: 10A MAX, Please enhance heat sink if exceed 6A (The larger voltage difference between input and output, the smaller output current)
Constant Current Range: 0.2-10A
Output Power: 600W (max), suggest to leave some slack for long time work
Working Temperature: -40 to +85 degree Celsius (Please enhance heat sink for over-temperature)
Operating Frequency: 150KHz
Conversion Efficiency: 92%-96% (Efficiency is related to input, output voltage, current and voltage difference)
Input Reverse Connection Protection: NO
Mounting Type: 4PCS 3mm screw hole
Connection Mode: Lead wire output
Module Size: 85x52x21mm(LxWxH)
Output voltage/current regulation method:
1. Adjust the CV-ADJ potentiometer to set the output voltage to the desired voltage according to your battery or LED.
2. Turn CC-ADJ potentiometer clockwise for about 30 turns, set the output current to the minimum, connect the LED, and turn CC-ADJ potentiometer to the current you need. If it is used for battery charging, after the battery is fully discharged, and then connected to the output, adjust CC-ADJ potentiometer to the current you need (the more residual battery power, the lower charging current).
Please do not use short circuit to adjust the current, otherwise it will damage the module.
The module is a booster module, the input voltage should be 2V lower at least than the output voltage.
Input and output cannot be reversed.
The input voltage shall not be less than 10V or more than 60V.
1x 600W Constant Voltage and Constant Current Power Module
Compare with similar items
There was a problem filtering reviews right now. Please try again later.
By a strange coincidence the board footprint is almost identical to the Raspberry Pi 3 and 4 B. Which is convenient. I would have lined up the mounting holes with the Pi, but you can't have everything. If you're going to play with DC powered stuff in this range and your Pi, it's a nice addition to the toybox.
The price is very reasonable for what you get.
Shipping was amazingly fast. Like, how do they do that? That fast.
I would not recommend these as they fail after very little use.