Currently unavailable.
We don't know when or if this item will be back in stock.

Have one to sell?

Geekworm ESP32 WROVER PCB Development Board with 8MB PSRAM WiFi+Bluetooth Low Power Consumption Dual Cores ESP32

3.8 out of 5 stars 21 ratings

Currently unavailable.
We don't know when or if this item will be back in stock.
    This fits your .
  • Make sure this fits by entering your model number.
  • Geekworm ESP32 WROVER-i DevKit is a low-footprint, minimal system development board which is powered by our latest ESP32-WROVER PCB module and can be easily adjusted to a breadboard, and build in ESP32-WROVER Module PCB version module.
  • Built around the ESP32-WROVER Module PCB module, this minimal system development board achieves optimal performance with its rich peripheral set, Wi-Fi and Bluetooth radio solutions, which are offered by our latest SoC, the ESP32. The limit is your imagination!
  • Get right into application design and development without worrying about RF performance and antenna design. The DevKitC has your basic system requirements already covered. Just plug in the USB cable and you’re good to go!
  • The WROVER DevKit contains the entire basic support circuitry for the ESP32-WROVER Module, including the USB-UART bridge(CH340), reset- and boot-mode buttons, LDO regulator and a micro-USB connector. All pin export GPIO is available to the developer.
  • Trouble shooting(also in the last description below) & Download: Pleaser refer to our wiki: www.raspberrypiwiki.com/index.php/ESP32_WROVER-i_DevKit

iPhone SE and Wireless Plans presented by Amazon $10/month gift card credit back on Cricket pre-paid plan and iPhone


Special offers and product promotions

Have a question?

Find answers in product info, Q&As, reviews

There was a problem completing your request. Please try your search again later.
All Product Information Customer Q&A's Customer Reviews

Your question may be answered by sellers, manufacturers, or customers who purchased this item, who are all part of the Amazon community.

Please make sure that you are posting in the form of a question.

Please enter a question.


Product Description

Note:

  1. Newest 8MB PSRAM, New ESP32-WROVER-B Chipset.
  2. This ESP32 WROVER PCB Development Board is based on ESP32-WROVER-B PCB antenna module, it comes with on-board antenna.
  3. In March 14 2019, this ESP32-WROVER development board has been updated to a new version with PCB antenna module according to the customer requirement. The previous IPEX antenna module version has been discontinued now.

[Packing List]

  • 1 x ESP32 WROVER PCB antenna Development Board

[Overview]

Geekworm ESP32 WROVER-i DevKit is a low-footprint, minimal system development board which is powered by our latest ESP32-WROVER PCB module and can be easily adjusted to a breadboard, and build in ESP32-WROVER Module PCB version module.

ESP32 WROVER PCB Development Board

[New and Powerful]

Built around the ESP32-WROVER Module PCB module, this minimal system development board achieves optimal performance with its rich peripheral set, Wi-Fi and Bluetooth radio solutions, which are offered by our latest SoC, the ESP32. The limit is your imagination!

[Rapid Prototyping]

Get right into application design and development without worrying about RF performance and antenna design. The DevKitC has your basic system requirements already covered. Just plug in the USB cable and you’re good to go!

[Flexible and Feature-Rich]

The WROVER DevKit contains the entire basic support circuitry for the ESP32-WROVER Module, including the USB-UART bridge(CH340), reset- and boot-mode buttons, LDO regulator and a micro-USB connector. All pin export GPIO is available to the developer.

[More details & Download]

please refer to the last short description

ESP32 WROVER PCB Development Board

[Trouble Shooting]

Q: How to use this board with arduino ide?

A: ESP32 WROVER is only a module of the ESP32 series, and ESP32's arduino documentation is suitable for esp32 wrover.please refer to here: github.com/espressif/arduino-esp32

Q: What to do if you have meet some problem with this development board?

A:

1.Please install the CH340 USB driver. In addition, please restart the computer. For the CH340 USB driver, please refer to: raspberrypiwiki.com/index.php/File:CH341SER.ZIP

If you can't find the device, please temporarily remove other USB devices and try again. (Note: There are some unknown reasons that may interfere. Sometimes we also find that the USB device cannot be found during the test.)

2.It is probably that the driver's conflict problem caused our WROVER can not to be recognized; or you can try to use a new computer to test.

3.Now the ESP32 WROVER PCB Development Board has updated with 8MB PSRAM, and the board write 4MB PSRAM as the PCB do not update, but actually it use ESP32-WROVER-B Module with 8MB PSRAM. The development board is depends on the ESP32-WROVER module. please refer to: espressif.com/sites/default/files/documentation/esp32-wrover_datasheet_en.pdf

4.We just bring out the PIN of this ESP32 WROVER-B module to facilitate the use of developers. We added the CH340 USB driver chip on it.


Product information


Customer Questions & Answers

Customer reviews

3.8 out of 5 stars
3.8 out of 5
21 customer ratings
How does Amazon calculate star ratings?
Reviewed in the United States on January 18, 2019
Verified Purchase
review imagereview imagereview image
6 people found this helpful
Comment Report abuse
Reviewed in the United States on August 13, 2019
Verified Purchase
One person found this helpful
Comment Report abuse
Reviewed in the United States on April 24, 2019
Verified Purchase
2 people found this helpful
Comment Report abuse
Reviewed in the United States on September 27, 2019
Verified Purchase
review image
Reviewed in the United States on July 7, 2019
Verified Purchase
Reviewed in the United States on May 9, 2019
Verified Purchase
Reviewed in the United States on August 9, 2019
Verified Purchase
Reviewed in the United States on March 3, 2019
Verified Purchase
Pages with related products. See and discover other items: PCB Antennas