NES case for Raspberry Pi 3,2 and B+ by Old Skool Tools
|Price:||$19.85 & FREE Shipping on orders over $25. Details|
Fulfillment by Amazon (FBA) is a service we offer sellers that lets them store their products in Amazon's fulfillment centers, and we directly pack, ship, and provide customer service for these products. Something we hope you'll especially enjoy: FBA items qualify for FREE Shipping and .
If you're a seller, Fulfillment by Amazon can help you increase your sales. We invite you to learn more about Fulfillment by Amazon .
- Enter your model number to make sure this fits.
- NES case specifically designed for Raspberry Pi 3, 2 and B+
- This firm design, made out of plastic is held together with the 4 provided bolts
- Easy access to the SD-Card and all other ports without opening the case
- Inspired by the Nintendo Entertainment System
Frequently bought together
Customers who bought this item also bought
Have a question?
Find answers in product info, Q&As, reviews
Please make sure that you are posting in the form of a question.
The Nintendo Entertainment System inspired Raspberry Pi case was designed to relive childhood memories. This unique design is made out of durable plastic and was designed to fit perfectly on the Raspberry Pi 3,2 and B+. We're all about bringing the Old Skool back! The 4 provided screws assure that the case is very firm and steady. The NES case provides access to every outlet of the Raspberry Pi without opening the case. The air vents provide good ventilation while in use. Note. This is just the case, Raspberry Pi is not included.
Top customer reviews
*** To make your own Red Led Power light ***
--- This Kit linked below has all the components needed to add Red Led Light
--- CanaKit Raspberry Pi GPIO Breakout Board / Cobbler Bundle (40-Pin T-Shaped - Assembled)
--- Aketek 50 PCS Jumper Wires Premium 200mm M/F Male-to-Female
* 1 Red LED
* 1 Red Jumper Cable
* 1 Black Jumper Cable
* 1 10K Ohm Resistor ( in the strip of 5 )
* Black Electrical Tape
* Hot Glue Gun ( Vastar Hot Glue Gun with 30 Pieces Melt Glue Sticks Melting Adhesive Glue Gun Kit for DIY Small Craft and Quick Repairs in Home & Office, 20 Watt )
* Soldering Iron ( Vastar Full Set 60W 110V Soldering Iron Kit - Adjustable Temperature, 5pcs Different Tips, Desoldering Pump, Stand, anti-static Tweezers and Additional Solder Tube for Variously Repaired Usage
--- Pics included to show steps ---
*** Keep in mind the Longest leg on LED light is the +Positive side
*** Using Red Jumper cable for +Positive, solder end to 10K Ohm Resistor
*** Solder other end of 10K Ohm Resistor to +Positive end of LED light
*** Using Black Jumper cable for Ground, solder that to the other leg of LED light (shorter end)
*** Connect other end of Red Jumper cable to spot 4 on GPIO of Raspberry Pi 3
( Diagram included for GPIO on Raspberry pi included with Kit above )
Pic included but on right side it's the 2nd and 3rd down from top 4-6
*** Connect other end of Black Jumper cable to spot 6
*** If it lights up, then proceed to wrapping each cable in Electrical tape, i then taped both sides
together but only after you wrap them independently to avoid contact with each other.
*** Using Hot Glue Gun to place and secure the cable and LED to hole. I used a small amount first under
the LED light to give it something to rest on, then proceeded to tack it down
That's it, and a Big thanks to Old Skool Tools for making this beautiful little case for us to enjoy ;)
I wish it were easier to cut out the buttons in order to make them functional, either by perforating or adding indentations around them. I taped around them and repeatedly cut around them with a very sharp utility knife. Even though I was as careful as possible, I still made a few scratches on the front that I wasn't able to buff out. My only gripe, and not enough to warrant a reduced review.
All of the ports are easily reachable, including the sd card slot on the back. Very well made and adorable.
Suggestions would be to add functioning buttons to the front as well as add that black stripe for cosmetics. Cool item and I have bought a couple for friends as well.
The halves fit together really well.
The hinge on the front (that covers the USB ports) feels nice and functions perfectly.
They even sent extra instructions on how to get RetroPie installed and setup.
If you are building an emulator using a pie product this is a nice way to make it look nice and clean next to your tv. Without this it would have been a fragile looking computer chip sitting on the entertainment center.
I would by another if I ever had the need for 2 of these I would by another.