Other Sellers on Amazon
+ Free Shipping
3 Pin Bow Sight - Fiber, Brass Pin, Aluminum Machined - Right and Left Handed
|Price:||$13.89 & FREE Shipping|
- Enter your model number to make sure this fits.
- Material:6061-T6 aluminum
- Fiber optic diameter:0.029" color:red,green
- Level with two vertical bars
- Adjustable for left and right handed shooters
- Markings for elevation and windage
Frequently bought together
Customers who bought this item also bought
Details: Material:6061-T6 aluminum CNC machined Long tumble to remove any machined mark Pins material:Brass Fiber optic diameter:0.029" color:red,green Shake-test passed Level with two vertical bars Adjustable for left and right handed shooters Markings for elevation and windage
Would you like to tell us about a lower price?
Top customer reviews
There was a problem filtering reviews right now. Please try again later.
Inexpensive, all metal sight. Seems pretty well made for 13 bucks. Even has a threaded hole in case you want to install a flashlight. As far as folk stripping out the sight pin adjustment screws, Id think that could happen on any sight. Just gotta be a little more gentle I guess. The screws are quite small in the first place. I'm pretty sure that there isn't any need to torque them.
My first archery deer was taken using this sight in November, and it performed well. The sight isn't terribly bright in really low light, but is satisfactory until the last 15 minutes of legal hunting hours. I did end up torquing my shot slightly on the deer, which I attribute to my not paying attention to the very small level.
Having purchased this sight allowed me to understand what I was looking for in a replacement, and I ended up purchasing a second hand Sword Apex Hunter with 0.010" pins. Note that this is also an inexpensive sight, but it has a larger level, significantly smaller pins, and collects more light for brighter pins towards the limits of legal shooting hours. I will keep the reviewed sight for backup purposes, as it performed well and may be used for another bow in the future.
first, I would like that to say that the site itself is a very quality piece of aluminum, with bright elevation and right to left markings. the pins illuminate very well, which has a awesome site picture. after getting this item and a peep site, I installed them on my PSE bow with no problems, other than typical "which screw tightens what". after that, I put the bow up til I could start my dialing in of all the pin placements.
once, I got a chance to shoot the bow with everything installed, I noticed that it was way off center, and the screws were loosening up. so once I looked at the site again and how I had understood it to be installed, I repositioned the site on the right side of the bow, with the right to left bar as far right as possible. this moved my arrow grouping to the correct right to left position on my target. once I got that corrected, I moved my pins up and down to the correct position, and got my bottom pin set at a 10 yard right under target placement, and a dead on placement at 15 yards.
so here is a short breakdown of the sight: (make sure you have a multi-size alan wrench tool, that goes from a large size to a very small wrench, I think the smallest head on this site; is 3/32)
1.) the site is made out of sturdy solid cast aluminum.
2.) install site on the correct side of your bow. that sounds simple, but depending on the type of site you have existing on your bow that you are replacing, this site might have to go opposite of that original side. after correct placement of the site, use locktite on your screws, to secure that site to your bow.
3.) lock in the level and fiber optic wire with epoxy glue, as in previous reviews these items were the first to fall off and get lost. use a clear epoxy, that won't turn a yellow color.
4.) tighten all placement screws for your right to left bar, and the elevation bar (which holds the pins, the large round thing that sits in the groove on the right to left bar). you should line up your right to left bar, so that your pins are inline with your bow string, and set your elevation bar as is or in the middle, since you will be adjusting your pins for elevation not that bar.
5.) shoot your bow a few times to see if anything becomes loose or less tight, if it does, see if you can retighten.
6.) if everything is pretty tight after a few test shots, then start moving your pins up and down.
this is my initial review, how this site holds up to real world hunting and in the woods is another story. we will see this weekend as I am going bow hunting, and if it falls to pieces I will let you all know.