Facebook Twitter Pinterest
Currently unavailable.
We don't know when or if this item will be back in stock.
Have one to sell? Sell on Amazon

Puget Systems Acrylic Enclosure for NVIDIA Jetson TX1

3.8 out of 5 stars 4 customer reviews
Currently unavailable.
We don't know when or if this item will be back in stock.
    This fits your .
  • Enter your model number to make sure this fits.
  • Includes mount points for a single 2.5inch 7mm hard drive on the top of the chassis using a SATA power/data extension cable.
  • This simple case for the NVIDIA Jetson Tegra X1 board is great for providing basic protection while still allowing full access to the many i/o ports and connectors on the board. It is made from nicely laser-cut and etched acrylic, and is simple to assemble or dis-assemble.
Currently unavailable. We don't know when or if this item will be back in stock.

Product Description

Included components: 1x Bottom acrylic panel 1x Top acrylic panel 4x .25 inch #6-32 standoffs (for under the Jetson TX1 board) 4x 1.125 inch #6-32 standoffs (for on top of the Jetson TX1 board) 4x Thin acrylic spacer (between Jetson TX1 board and 1.25 inch standoffs) 4x .375 inch #6-32 screws (for securing the top panel to the 1.25 inch standoffs) 1x Acrylic SSD spacer 4x 12mm M3x0.5 screws (for mounting an SSD) 1x 12inch SATA power/data extension cable 4x .5 inch rubber feet If you wish to stack multiple kits together, we have also included: 4x Thick acrylic spacers 4x .75 inch #6-32 socket cap screws 1x 7/64 inch hex key

Product Information

Technical Details

Collapse all
Other Technical Details

Additional Information

Warranty & Support

Amazon.com Return Policy:You may return any new computer purchased from Amazon.com that is "dead on arrival," arrives in damaged condition, or is still in unopened boxes, for a full refund within 30 days of purchase. Amazon.com reserves the right to test "dead on arrival" returns and impose a customer fee equal to 15 percent of the product sales price if the customer misrepresents the condition of the product. Any returned computer that is damaged through customer misuse, is missing parts, or is in unsellable condition due to customer tampering will result in the customer being charged a higher restocking fee based on the condition of the product. Amazon.com will not accept returns of any desktop or notebook computer more than 30 days after you receive the shipment. New, used, and refurbished products purchased from Marketplace vendors are subject to the returns policy of the individual vendor.
Product Warranty: For warranty information about this product, please click here

Feedback

If you are a seller for this product, would you like to suggest updates through seller support?
Would you like to tell us about a lower price?
Customer Questions & Answers
See questions and answers

Customer Reviews

Top Customer Reviews

3.0 out of 5 starsOk, does the job.
By datajerk on November 13, 2016
Verified Purchase
The good:

1. It serves its purpose.
2. SATA cable included.

The bad:

1. Instead of using bolts, like other acrylic sheet cases, this case uses threaded holes in the acrylic (filled with debris). Special care needs to be taken when screwing in the standoffs.
2. The thin plastic spacers used to bolt the longer posts to the standoffs only allows about a 1/2 turn making the posts pop out if lateral pressure is applied. I ended up not using them and did not have any issues. I speculate their utility is to support larger SATA drives. If that is the case then a taller post should have been included. If I need more height I can get other posts from Mouser I suppose. My SATA drive is quite thin, so not a problem for me.
3. The SATA spacer is too thin for the included SATA cable so a bit of lateral pressure is constantly being applied to the drive connector. I guess the upshot is that the cable will not pop out (like it does on the TX1 board).
4. The case is larger than it needs to be. I speculate this is for stacking. Stacking could have been done using the exiting posts like the Geauxrobot cases do for the RPI. The larger boarder makes it a bit more cumbersome to work with the GPIO pins. Not impossible, just cumbersome.

Given the negatives I still would have purchased this case because of the lack of obvious alternatives. Perhaps I need to look harder.
1 Comment Was this review helpful to you? Yes No Sending feedback...
Thank you for your feedback.
Sorry, we failed to record your vote. Please try again
Report abuse
4.0 out of 5 starsWell-crafted, a bit pricey. Looks awesome, but needed?
By Hal C. Elrod on July 29, 2016
Verified Purchase
I purchased when I ordered TX1 board. I didn't want the board shorting out sitting on my desk. But the new boards already come with feet, and are probably adequately situated as-is.

That said, the Puget Systems enclosure is a work of crystal-like art. It fits exactly, and comes with mounting points and SATA adapter for an SDD. The button labels are laser-etched or some-such, which is a pro. Definitely shows off the TX1 to maximum advantage.
Comment Was this review helpful to you? Yes No Sending feedback...
Thank you for your feedback.
Sorry, we failed to record your vote. Please try again
Report abuse
3.0 out of 5 starsIt is basically a base plate, a piece of ...
By K. Norton on September 3, 2016
Verified Purchase
It is basically a base plate, a piece of plexiglass (with their tacky logo dominating it), and a few pieces of hardware. If I was going to do it again I would make my own for $5.
Comment Was this review helpful to you? Yes No Sending feedback...
Thank you for your feedback.
Sorry, we failed to record your vote. Please try again
Report abuse
5.0 out of 5 starsFive Stars
By Eric Jenkinson on October 3, 2016
Verified Purchase
Great product with great customer service.
Comment Was this review helpful to you? Yes No Sending feedback...
Thank you for your feedback.
Sorry, we failed to record your vote. Please try again
Report abuse

There's a problem loading this menu right now.

Learn more about Amazon Prime.