Other Sellers on Amazon
+ $2.50 shipping
1 X Stainless Works™ Stainless Steel Beverage Dispenser Replacement Spigot(Polished Finish)
Fulfillment by Amazon (FBA) is a service we offer sellers that lets them store their products in Amazon's fulfillment centers, and we directly pack, ship, and provide customer service for these products. Something we hope you'll especially enjoy: FBA items qualify for FREE Shipping and .
If you're a seller, Fulfillment by Amazon can help you increase your sales. We invite you to learn more about Fulfillment by Amazon .
- Enter your model number to make sure this fits.
- Needs 5/8 inch or 16mm diameter opening to install. For flat surface
- can fit up to 1 inch hole. (For 1/2 inch opening
- please click on "stainless works" for other design and options)
- Stainless Steel Constructions
- No Lead
- Acid Resistant. Great for Dispensing Tea
Frequently bought together
Customers who bought this item also bought
Compare to similar items
This item 1 X Stainless Works™ Stainless Steel Beverage Dispenser Replacement Spigot(Polished Finish)
|Shipping||FREE Shipping||FREE Shipping||FREE Shipping||FREE Shipping|
|Sold By||Decent Solution||RichWealth||RichWealth||RichWealth|
|Color||Polished Stainless Steel||Silver||Silver+black||Silver|
|Material Type||Stainless Steel||Stainless Steel||Stainless Steel||Stainless Steel|
Stainless Works® Stainless Steel Spigot is designed to replace the cheap, easy to break and leaky plastic spigot on the market. Our spigots look elegant, feel solid, and last a lifetime(backed up by our life time warranty)Stainless Works® SSS010 Use and Care Instruction:
Before installation, wash in soapy water and rinse suggested
Remove the nut, and one set of washer, gasket from the spigot
Insert the spigot to the despenser
Install the gasket and washer
Tight the nut. Usually hand-tight is good enough to create a water tight seal. You can also use 3/4 in wrench. Do not over-tighten, it could crack the despenser made of fragile material like glass or ceramic.
After each use, rinse throughly with clean water with handle in partial open position(45 degree turn)
If used for sugary drink, we suggest that remove spigot from the dispener and clean throughly.
Package Content: 1 stainless steel spigot, 2 stainless steel washer, 2 silicon gasket, 1 stainless Steel nut. Warranty informaton is provided on the package.
Our Staineless Works® Products:
SSS010: Best Flow Rate at 3 sec/cup with 8 inch water
SSS012: Fits smaller holes(12mm or half inch), Flow Rate at 5 sec/cup
SSS016: Smoothest and effortless turning with limited flow, Flow Rate at 9 sec/cup
SSS020: Classic Design, Good Value. Flow Rate at 7 sec/cup .
We are selling spigot with chalkboard labels.
Check Model Number: SSS010-10L, SSS012-10L and SSS016-10L
Top Customer Reviews
I bought a pair of glass beverage dispensers for making kombucha. (2 of Stylesetter Glass Beverage Dispenser- 169-Ounce) The only thing wrong with them was the plastic spigots that were supplied. They were junk.
I bought a pair of these stainless spigots, installed them, and they work perfectly.
I would buy these again in a heartbeat, but as I said, I expect I won't need to. These things look bulletproof.
That's where this spigot comes in. There are plenty of 3/4 in. (19mm) replacement spigots out there, but this is the only one I could find that was 5/8 in (~16mm), which is the size I needed for my jar. I even went to a couple of hardware stores looking for parts I could modify or put together for my purposes, but I couldn't find anything I would trust with the acidity of kombucha. The price was a little more than I wanted to pay, but since it was the only one I could find that was the right size and it is stainless steel, I went ahead and ordered it from Amazon.
I ordered the valve on the weekend and it arrived on Tuesday. It came in a bubble envelope. The spigot itself was wrapped with foam in a small box, so it was well protected. The exterior parts are all stainless steel. The finish is much nicer than I expected. Looking down inside from the back, I could see that the valve was a nice ball valve that FULLY opens, and not the funky plate type the other one had. The valve opening looked to be at least 1/4 in. (~6mm) wide. I don't recall exactly, but I think the ball valve inside was brass, but not totally certain on that point. I installed it before I took a second look to verify this.
The installation was as easy as removing the old spigot and putting this one on. It has two silicon washers backed by stainless steel housings shaped to match the shape of the washers. They compressed the silicon washers well enough to get a good seal at just finger tightness, but I went ahead and gave it two more turns with a wrench to make sure. The silicon washers did not deform enough to cause me any worry that I had messed up the seal.
Then I filled my glass jar half way. There were no leaks at all. Then I opened the valve all the way. The flow rate was really nice. Much better than the stock spigot. Also, controlling the flow rate was easy. It backs down nicely so you can get the flow rate just right for you. The ball valve should not clog with the stingy stuff from kombucha or lemonade or whatever you should flow through it, and even if it did it should be a breeze to clean. The spigot has a nice solid feel to it with a slight detent that happens when it moves into the fully open position. This is a nice touch.
This is the only five star rating I've ever given. And that is because the item exceeded my expectations, even at twice the price of other replacement spigots.
The spout has a nice movement to the handle-like another reviewer said-its smooth operating-won't flip out of your hand or cause liquid to splash like other push down/pull up handled spouts. Its very heavy-substantial-something that could withstand a lot of use and abuse without any ill effect.
This is the quality that I would expect from a professional plumbing fixture (from a name brand company-not the cheap home store fixtures-its actually better than many things I've installed in my plumbing-because like it or not-its all got plastic/rubber parts that deteriorate) or an antique spout-something that was well made to last indefinitely and shows almost no change in appearance due to the finishing/design over time. I expect to have this spout forever! I can reuse it on any similar sized opening in a gravity feed jar.
As a side note-I am a ceramicist and I will be making beverage dispensers soon because of this product. I never considered it before because I didn't think there were any quality (non plastic or plastic component containing) spouts out there. I was worried about leaks-since I have never encountered a spigot that doesn't leak. Now I can order some of these and make all manner of ceramic beverage vessels-knowing I won't be wasting my time.
The only drawback I can think of is that because its metal-it won't work for people making Kombucha or water Kefir or similar fermented drinks.
other than that-I am seriously advocating this spout. If you're like me and would rather pay once for something with great longevity and good design, than buy inferior future trash-you won't hesitate to purchase this-or several.