Qty:1

Other Sellers on Amazon
Add to Cart
$29.47 ($0.59 / Bolts)
+ Free Shipping
Sold by: BIC Warehouse
Add to Cart
$30.82 ($0.62 / Bolts)
+ Free Shipping
Sold by: Gatzies
Add to Cart
$22.44 ($0.45 / Bolts)
+ $8.63 shipping
Sold by: Zack Electronics Inc
Have one to sell? Sell on Amazon

TOGGLER SNAPTOGGLE BB Toggle Anchor, Zinc-Plated Steel Channel, Made in US, 3/8" to 3-5/8" Grip Range, For 1/4"-20 UNC Fastener Size (Pack of 50)

4.7 out of 5 stars 30 customer reviews

Price: $29.92 ($0.60 / Bolts) & FREE Shipping on orders over $49. Details
In Stock.
Ships from and sold by Amazon.com.
9 new from $22.44

Specifications for this item
Brand Name TOGGLER
Part Number 25014
UPC 036296250140
Material Type Plastic and Zinc Plated Steel
System of Measurement Inch
Thread Size 1/4"-20
Specification Met FF-B-588-D Type V
EAN 0036296250140
Exterior Finish Zinc Plated
Fits Hole Size 1/2 inches
Included Components Anchors Only
Item Weight 2.15 pounds
Manufacturer Series Number SNAPTOGGLE BB
Maximum Compatible Thickness 3.625  inches
Minimum Compatible Thickness 0.375  inches
Number of Items 50
Outside Diameter 1/2  inches
Style Name Toggle
Thread Coverage Partially Threaded
Thread Style UNC
UNSPSC Code 31162100
Wing Span 2  inches

A Full Selection of Hydraulic, Pneumatic & Plumbing Products
pipe fittings
Pipe Fittings
seals
Seals
hydraulic valves
Hydraulic Valves
flow control and filtration products
Shop all

Frequently Bought Together

  • TOGGLER SNAPTOGGLE BB Toggle Anchor, Zinc-Plated Steel Channel, Made in US, 3/8" to 3-5/8" Grip Range, For 1/4"-20 UNC Fastener Size (Pack of 50)
  • +
  • The Hillman Group 90413 1/4-20-Inch x 2-1/2-Inch Round Head Combo Machine Screw, 100-Pack
  • +
  • Steel Flat Washer, Plain Finish, ASME B18.22.1, 1/4" Screw Size, 9/32" ID, 5/8" OD, 0.065" Thick (Pack of 100)
Total price: $48.20
Buy the selected items together

Product Features

  • Toggle anchor installs behind 3/8"- to 3-5/8"-thick hollow materials including gypsum board, drywall, and concrete block to provide a secure hold from within the mounting material
  • Anchor affixes to the wall before adding the bolt and fixture, allowing one-person installation and fixture changes
  • Made in USA, and works with 1/4"-20 UNC-threaded metal bolts (sold separately)
  • Ultimate tensile strength is 265 lb. in 1/2" drywall and 1,080 lb. in concrete block with a 1/4"-20 UNC bolt
  • Use one-fourth or less of listed maximum values for safe working loads (as required by local regulations)

Product Description

The TOGGLER SNAPTOGGLE BB toggle anchor provides a secure hold from within various hollow materials 3/8" to 3-5/8" thick including gypsum board, drywall, and concrete block, and is made in USA. The anchor requires a 1/4"-20 UNC-threaded metal bolt with a minimum length equal to the thickness of the item being fastened and the thickness of the mounting material plus 1/2". The anchor channel will not rotate when installing the bolt, whether installing by hand or with a screw gun, and will stay in place if the bolt is removed to facilitate fixture and screw changes. The SNAPTOGGLE anchor meets Federal Specification FF-B-588-D for Type V anchors.

The anchor consists of a corrosion-resistant zinc-plated steel anchor channel that inserts through a 1/2" drilled hole in walls, ceilings, or floors and installs against the back side of the mounting material; plastic straps attached to the channel that position it into place; and a plastic cap that slides down the straps and presses into the drilled hole firmly to lock the anchor channel in place behind the mounting material. Once the cap is set in place, the straps snap off by hand. The item being fastened affixes to the mounting material by inserting a bolt through the item, into the drilled hole, and through the anchoring channel behind the material and tightening.

Specifications

Ultimate Tensile and Shear Strength Values

MediaDrill DiameterBolt DescriptionUltimate Tensile StrengthUltimate Shear Strength
1/2" Drywall1/2"1/4"-20 UNC zinc-plated steel265 lb.241 lb.
5/8" Drywall1/2"1/4"-20 UNC zinc-plated steel356 lb.324 lb.
1/2" Drywall with 25 Gauge Stud*1/2"1/4"-20 UNC zinc-plated steel425 lb.Not available
5/8" Drywall with 25 Gauge Stud*1/2"1/4"-20 UNC zinc-plated steel464 lb.Not available
Concrete Block1/2"1/4"-20 UNC zinc-plated steel1,080 lb.Not available

*Failure measured as breakage of drywall portion.

Warning: Use one-fourth or less of listed maximum values for safe working loads (as required by local regulations). For more information, see the manufacturer's technical bulletin.

Anchors provide reinforcement to a fastener that would otherwise have insufficient hold in substrates such as concrete, brick, stone, drywall, or other materials for a particular application. The fastener may be included with or integrated into the anchor itself, or it may be sold separately. Anchors provide support through various methods, including expansion from within or behind the substrate or even adhesive compounds.

TOGGLER Anchor System manufactures wall anchors and toggle bolts. The company, founded in 1968, is headquartered in Norwalk, CT.


Product Details

Data Sheet [405kb PDF]| Technical Guide [181kb PDF]
  • Product Dimensions: 9 x 6 x 3 inches ; 2.2 pounds
  • Shipping Weight: 1.8 pounds (View shipping rates and policies)
  • Domestic Shipping: Item can be shipped within U.S.
  • International Shipping: This item is not eligible for international shipping. Learn More
  • ASIN: B0051IARUE
  • Item model number: 25014
  • Average Customer Review: 4.7 out of 5 stars  See all reviews (30 customer reviews)
  • Amazon Best Sellers Rank: #16,429 in Industrial & Scientific (See Top 100 in Industrial & Scientific)
  • Manufacturer’s warranty can be requested from customer service. Click here to make a request to customer service.

Important Information

Directions

Drill a 1/2" (13mm) hole. Hold metal channel flat alongside plastic straps and slide channel through hole. Minimum clearance behind wall: 1-7/8" (48mm).

Hold ends of straps between thumb and forefinger and pull toward you until channel rests flush behind wall. Slide plastic cap along straps with other hand until flange of cap is flush with wall.

Snap straps at wall by pushing side to side, snapping off straps level with flange of cap.

Place item over flange. Insert bolt through item and tighten until flush against item, then stop.

Use machine screw or bolt to match thread in channel: BB (1/4"-20). Bolt length = item thickness + wall or ceiling thickness + 1/2" (13mm)


Customer Questions & Answers

Customer Reviews

Top Customer Reviews

By HMMWV VINE VOICE on March 19, 2011
We're all familiar with the old fashioned molly fasteners - most usually had a head about the size of a dime with a couple spikes and a machine screw that, after poking through the drywall expanded the 4 "wings" of the molly until they gripped the back of the drywall.

This is a similar system, but much stronger, and meant for harsher loctions. For example, I have the largest hoffman box container bolted to the side of my house to house my pbx and network equipment so that when the phone company comes out their dmarc is just 8 feet down from where the pbx is and there is no quibbling over who's fault it is (I use a DID trunk system with 100 numbers for inward dialing and a DOD outbound trunk with about 30+ extensions used inside my house - it is definitely not your "normal" house phone system, but a full northern telecom busines system with 130 phone numbers allocated to it, plus I have uverse in the hoffman box - all of that is supported by just 4 of these bolts and a couple pieces of unistrut!

We never did drill into a stud trying to mount this - studfinders didn't work through stucco so the only option was to go with the toggler. you insert the pivot back which has machine threads in the center through your drilled opening then afterwards use the plastic sticks which closely resemble ty-wraps in that they have a bunch of clicks on them to let you pull it tight so it won't drop into the wall. Afterwards, you can put any 1/4 x 20 tpi bolt into it and tighten it up snug.
Read more ›
Comment 10 people found this helpful. Was this review helpful to you? Yes No Sending feedback...
Thank you for your feedback.
Sorry, we failed to record your vote. Please try again
Report abuse
Verified Purchase
These are a great item you can use for hanging dang near everything at a price that has the Big Box hardware stores beat, my only word of caution is that unlike the smaller qty. packages these do not come with fasteners so either buy them from Amazon or plan a trip to your local hardware store.
Comment 7 people found this helpful. Was this review helpful to you? Yes No Sending feedback...
Thank you for your feedback.
Sorry, we failed to record your vote. Please try again
Report abuse
Verified Purchase
These are GREAT mounts. far superior to the old school butterfly type metal hinged nut.
These can take some getting used to the first time, and are sensitive to things behind the wall snagging ... but after you get used to the way the metal slides behind the surface, they are unbeatable in performance.
Comment Was this review helpful to you? Yes No Sending feedback...
Thank you for your feedback.
Sorry, we failed to record your vote. Please try again
Report abuse
Verified Purchase
Can not say enough about these. They are the Boss in toggles and hangers. The only thing that would make them better is if they were offered with matching screws. The reason they are not matched is because you might need longer or shorter depending on wall or ceiling products, thicknesses, layers, etc. Get them, and get plenty. You'll love them. Oh ya, I try to mention every chance I get, MADE IN THE U.S.A.
1 Comment Was this review helpful to you? Yes No Sending feedback...
Thank you for your feedback.
Sorry, we failed to record your vote. Please try again
Report abuse
Verified Purchase
Excellent product! Sure beats Moly's. The actually work as advertised. During the mounting of the back bracket on a concrete wall, I used hex head 1/4-20 machine screws with these anchors. They do not come with the screws/bolts.
Comment Was this review helpful to you? Yes No Sending feedback...
Thank you for your feedback.
Sorry, we failed to record your vote. Please try again
Report abuse
Verified Purchase
These are the best anchors out there. Extremely easy to install and have way more load capacity then any other anchor. Obviously they don't come with the bolts/hardware because they fit ANY WALL from 3/8" to 3-1/2". Would you expect them to provide every bolt size for every possible wall thickness in that range for every anchor that comes in this kit? Of course not.
Comment Was this review helpful to you? Yes No Sending feedback...
Thank you for your feedback.
Sorry, we failed to record your vote. Please try again
Report abuse
Verified Purchase
If you use or have a need for toggle bolt style anchors, these are excellent. I use them for hanging flat panel TV's on steel stud sheetrock walls by drilling through the stud so that the anchor is behind the steel.
Comment Was this review helpful to you? Yes No Sending feedback...
Thank you for your feedback.
Sorry, we failed to record your vote. Please try again
Report abuse
By Mikemo on August 1, 2013
Verified Purchase
Very clever product for anchoring items to walls. The toggle design is clever and easy to install in walls of multiple thicknesses. Used it to mount a very heavy video conferencing system to an office wall. A little pricy, but worth it in my opinion.
Comment Was this review helpful to you? Yes No Sending feedback...
Thank you for your feedback.
Sorry, we failed to record your vote. Please try again
Report abuse

Most Recent Customer Reviews