UPDATE: I have gone through quite the upgrade process. I originally got the 120 AIO as it was the only one that would fit in my case. the 120 worked very well, but my temps were still a little high on this 13700k, so I decided to get the 240 since my case supports it now. I got the same brand since IO was happy with the 120 and all the mounting brackets are the same. I left my two fans in the front of the case and decided on a pull configuration. Had to rewire 3 fans and the new pump so that took a while re doing the cabling. And then figuring out which way to orient the pump to minimize the stress on the water lines. Initial testing was great with Idle temps between 38-41 and peak temps of 81. After putting all the side covers and front panel back on I got idle temps around 45 and peak temps between 86-90. I wasnt getting much airflow out the front of the case so I took the front panel off and for now am leaving it off. I am back down to idel 37-38 and peak temps of 81-85. So I have reduced both my idle temps by about 6 degrees and peak temps by 15-20 degrees. And this AIO is super responsive as the watts come down the temps come down. I also did play with all of my fan settings for the pump and fans. I happen to use the stair instead of slope and also have the fans running at a higher percentage than the pump up until about 55 degrees to IMO keep the radiator as cool as possible. If you have room in your case the 240 definitely works better than the 120. I think the brand is good and both these pumps work great.
As a side note, before I upgraded to the 240, I ran a tube from my window AC into one of my input fans and near the back of the case where the radiator was. It made the radiator cold and all my internal temps were in the 20's and my high temp was around 60. I havnt tried that with the 240 yet. With everything so low in temps I gained 1000 points on my CPU benchmark. :)
ORIGINAL REVIEW: Lots of parts, not the greatest of instructions, but does a great job of cooling down the hot running I7 13700k processor. I had a little trouble getting the radiator to mount in place of my rear fan, so I ended up using the fan to pull across the radiator instead of pushing through it. My case just wasnt quite big enough for the radiator to replace the old case fan. I mounted the radiator first so I could figure out the best rotation of the pump to minimize any pull on the hoses. It would have been a lot faster had the radiator fit perfect, the mounting holes were a bit off from my case, but I just used 2 screws diagnol to mount it securely. This is my first water cooled system, so I was pretty leary of any leaks and still probable a little shy about having water in my case. But, my new processor was running so hot that I had to do something and thins was easier to install than some of the air cooled options and even cheaper. I dont have room for a 6" tall heatsink and fan and this fit the bill. Performance wise, I ran several CPU benchmarks and peaked at 95 c for a split second before it dropped below 60. The bulk of the CPU stress test, was around 60. The unit kicked in quickly and brought my temps down just as fast. Idle temp is around 41. As a bonus, my CPU mark actually increased anywhere from 900-1300 over what I was getting prior to this install. Basically I roughly went from 43000 to 44000 just by installing this unit. Honestly, I can probably squeeze more out of it because I had several background tasks running that I normally shut off. The power are all 3 pin not 4 and I am still not 100% sure of which MB plugs to use. I plugged the fan into the cpu fan header and the pump into the cpu pump/fan option header, but I also have another pump header on the MOBO. So IDK. The RGB lights plugged into my 4 pin on the MB and worked. I didnt test the included remote nor did I play around with the lighting. I was mostly concerned about the heat situation, which this thing rocked. There is an insane amount of wire length for the Lighting connections.
Overall, this thing is great, does a great job of cooling and is quiet.
Enjoy fast, FREE delivery, exclusive deals and award-winning movies & TV shows with Prime
Try Prime
and start saving today with Fast, FREE Delivery
Frequently bought together
$63.99
Get it as soon as Thursday, Aug 10
In Stock.
Total price:
To see our price, add these items to your cart.
Choose items to buy together.
Featured items you may like
Page 1 of 1 Start overPage 1 of 1
From the manufacturer
Motherboard Sync
Compatible with 5V ARGB capable motherboards from ASUS, Gigabyte, MSI, and ASRock.
High Performance Waterblock
A high-performance copper base plate increases heat conductivity for quieter, more effective CPU cooling.
-
Manual ARGB Controler
Switch between the following modes: Flow, Ripple, Pulse, Blink, Wave, Full Light, RGB Spectrum, and Off along with various colors and LED speed options.
-
Short and Sweet
A low-profile pump design provides quick liquid circulation, completely maintenance-free operation and dazzling lighting through the specially designed water block.
-
High Efficiency Radiator
The large surface increases the cooling performance and provides exceptional heat dissipation.
Small Package, Big Performance
The TH120 ARGB Sync combines a highly efficient radiator with a high static pressure fan to keep your CPU running cool
Videos
Page 1 of 1Start OverPage 1 of 1
Videos for related products
2:18
Click to play video
TH360 ARGB Motherboard Sync Edition Intel LGA1700 Ready
Thermaltake USA Direct
Videos for related products
2:21
Click to play video
TH360 ARGB Sync Snow Edition
Thermaltake USA Direct
Videos for related products
2:14
Click to play video
TH240 ARGB Motherboard Sync Snow Edition Intel LGA1700 Ready
Thermaltake USA Direct
Videos for related products
0:39
Click to play video
DeepCool LS720/LS520/LS320 High-Performance Liquid CPU Cooler
DeepCool
Videos for related products
16:57
Click to play video
Corsair iCue H100i Elite Carpellix liquid CPU cooler. BEST 1
Supa Syfy
Videos for related products
2:03
Click to play video
LIQMAX III Series All-In-One CPU AIO Liquid Cooler
LEPATEK CORPORATION
Super quiet and works great to cool down my I7 13700k
Reviewed in the United States on January 10, 2023
UPDATE: I have gone through quite the upgrade process. I originally got the 120 AIO as it was the only one that would fit in my case. the 120 worked very well, but my temps were still a little high on this 13700k, so I decided to get the 240 since my case supports it now. I got the same brand since IO was happy with the 120 and all the mounting brackets are the same. I left my two fans in the front of the case and decided on a pull configuration. Had to rewire 3 fans and the new pump so that took a while re doing the cabling. And then figuring out which way to orient the pump to minimize the stress on the water lines. Initial testing was great with Idle temps between 38-41 and peak temps of 81. After putting all the side covers and front panel back on I got idle temps around 45 and peak temps between 86-90. I wasnt getting much airflow out the front of the case so I took the front panel off and for now am leaving it off. I am back down to idel 37-38 and peak temps of 81-85. So I have reduced both my idle temps by about 6 degrees and peak temps by 15-20 degrees. And this AIO is super responsive as the watts come down the temps come down. I also did play with all of my fan settings for the pump and fans. I happen to use the stair instead of slope and also have the fans running at a higher percentage than the pump up until about 55 degrees to IMO keep the radiator as cool as possible. If you have room in your case the 240 definitely works better than the 120. I think the brand is good and both these pumps work great.As a side note, before I upgraded to the 240, I ran a tube from my window AC into one of my input fans and near the back of the case where the radiator was. It made the radiator cold and all my internal temps were in the 20's and my high temp was around 60. I havnt tried that with the 240 yet. With everything so low in temps I gained 1000 points on my CPU benchmark. :)ORIGINAL REVIEW: Lots of parts, not the greatest of instructions, but does a great job of cooling down the hot running I7 13700k processor. I had a little trouble getting the radiator to mount in place of my rear fan, so I ended up using the fan to pull across the radiator instead of pushing through it. My case just wasnt quite big enough for the radiator to replace the old case fan. I mounted the radiator first so I could figure out the best rotation of the pump to minimize any pull on the hoses. It would have been a lot faster had the radiator fit perfect, the mounting holes were a bit off from my case, but I just used 2 screws diagnol to mount it securely. This is my first water cooled system, so I was pretty leary of any leaks and still probable a little shy about having water in my case. But, my new processor was running so hot that I had to do something and thins was easier to install than some of the air cooled options and even cheaper. I dont have room for a 6" tall heatsink and fan and this fit the bill. Performance wise, I ran several CPU benchmarks and peaked at 95 c for a split second before it dropped below 60. The bulk of the CPU stress test, was around 60. The unit kicked in quickly and brought my temps down just as fast. Idle temp is around 41. As a bonus, my CPU mark actually increased anywhere from 900-1300 over what I was getting prior to this install. Basically I roughly went from 43000 to 44000 just by installing this unit. Honestly, I can probably squeeze more out of it because I had several background tasks running that I normally shut off. The power are all 3 pin not 4 and I am still not 100% sure of which MB plugs to use. I plugged the fan into the cpu fan header and the pump into the cpu pump/fan option header, but I also have another pump header on the MOBO. So IDK. The RGB lights plugged into my 4 pin on the MB and worked. I didnt test the included remote nor did I play around with the lighting. I was mostly concerned about the heat situation, which this thing rocked. There is an insane amount of wire length for the Lighting connections.Overall, this thing is great, does a great job of cooling and is quiet.
Reviewed in the United States on January 10, 2023
Images in this review
Top reviews from the United States
There was a problem filtering reviews right now. Please try again later.
Reviewed in the United States on January 10, 2023
As a side note, before I upgraded to the 240, I ran a tube from my window AC into one of my input fans and near the back of the case where the radiator was. It made the radiator cold and all my internal temps were in the 20's and my high temp was around 60. I havnt tried that with the 240 yet. With everything so low in temps I gained 1000 points on my CPU benchmark. :)
ORIGINAL REVIEW: Lots of parts, not the greatest of instructions, but does a great job of cooling down the hot running I7 13700k processor. I had a little trouble getting the radiator to mount in place of my rear fan, so I ended up using the fan to pull across the radiator instead of pushing through it. My case just wasnt quite big enough for the radiator to replace the old case fan. I mounted the radiator first so I could figure out the best rotation of the pump to minimize any pull on the hoses. It would have been a lot faster had the radiator fit perfect, the mounting holes were a bit off from my case, but I just used 2 screws diagnol to mount it securely. This is my first water cooled system, so I was pretty leary of any leaks and still probable a little shy about having water in my case. But, my new processor was running so hot that I had to do something and thins was easier to install than some of the air cooled options and even cheaper. I dont have room for a 6" tall heatsink and fan and this fit the bill. Performance wise, I ran several CPU benchmarks and peaked at 95 c for a split second before it dropped below 60. The bulk of the CPU stress test, was around 60. The unit kicked in quickly and brought my temps down just as fast. Idle temp is around 41. As a bonus, my CPU mark actually increased anywhere from 900-1300 over what I was getting prior to this install. Basically I roughly went from 43000 to 44000 just by installing this unit. Honestly, I can probably squeeze more out of it because I had several background tasks running that I normally shut off. The power are all 3 pin not 4 and I am still not 100% sure of which MB plugs to use. I plugged the fan into the cpu fan header and the pump into the cpu pump/fan option header, but I also have another pump header on the MOBO. So IDK. The RGB lights plugged into my 4 pin on the MB and worked. I didnt test the included remote nor did I play around with the lighting. I was mostly concerned about the heat situation, which this thing rocked. There is an insane amount of wire length for the Lighting connections.
Overall, this thing is great, does a great job of cooling and is quiet.
Color: BlackSize: 120mmStyle: ARGBPattern: CoolerVerified Purchase
Super quiet and works great to cool down my I7 13700k
Reviewed in the United States on January 10, 2023
UPDATE: I have gone through quite the upgrade process. I originally got the 120 AIO as it was the only one that would fit in my case. the 120 worked very well, but my temps were still a little high on this 13700k, so I decided to get the 240 since my case supports it now. I got the same brand since IO was happy with the 120 and all the mounting brackets are the same. I left my two fans in the front of the case and decided on a pull configuration. Had to rewire 3 fans and the new pump so that took a while re doing the cabling. And then figuring out which way to orient the pump to minimize the stress on the water lines. Initial testing was great with Idle temps between 38-41 and peak temps of 81. After putting all the side covers and front panel back on I got idle temps around 45 and peak temps between 86-90. I wasnt getting much airflow out the front of the case so I took the front panel off and for now am leaving it off. I am back down to idel 37-38 and peak temps of 81-85. So I have reduced both my idle temps by about 6 degrees and peak temps by 15-20 degrees. And this AIO is super responsive as the watts come down the temps come down. I also did play with all of my fan settings for the pump and fans. I happen to use the stair instead of slope and also have the fans running at a higher percentage than the pump up until about 55 degrees to IMO keep the radiator as cool as possible. If you have room in your case the 240 definitely works better than the 120. I think the brand is good and both these pumps work great.Reviewed in the United States on January 10, 2023
As a side note, before I upgraded to the 240, I ran a tube from my window AC into one of my input fans and near the back of the case where the radiator was. It made the radiator cold and all my internal temps were in the 20's and my high temp was around 60. I havnt tried that with the 240 yet. With everything so low in temps I gained 1000 points on my CPU benchmark. :)
ORIGINAL REVIEW: Lots of parts, not the greatest of instructions, but does a great job of cooling down the hot running I7 13700k processor. I had a little trouble getting the radiator to mount in place of my rear fan, so I ended up using the fan to pull across the radiator instead of pushing through it. My case just wasnt quite big enough for the radiator to replace the old case fan. I mounted the radiator first so I could figure out the best rotation of the pump to minimize any pull on the hoses. It would have been a lot faster had the radiator fit perfect, the mounting holes were a bit off from my case, but I just used 2 screws diagnol to mount it securely. This is my first water cooled system, so I was pretty leary of any leaks and still probable a little shy about having water in my case. But, my new processor was running so hot that I had to do something and thins was easier to install than some of the air cooled options and even cheaper. I dont have room for a 6" tall heatsink and fan and this fit the bill. Performance wise, I ran several CPU benchmarks and peaked at 95 c for a split second before it dropped below 60. The bulk of the CPU stress test, was around 60. The unit kicked in quickly and brought my temps down just as fast. Idle temp is around 41. As a bonus, my CPU mark actually increased anywhere from 900-1300 over what I was getting prior to this install. Basically I roughly went from 43000 to 44000 just by installing this unit. Honestly, I can probably squeeze more out of it because I had several background tasks running that I normally shut off. The power are all 3 pin not 4 and I am still not 100% sure of which MB plugs to use. I plugged the fan into the cpu fan header and the pump into the cpu pump/fan option header, but I also have another pump header on the MOBO. So IDK. The RGB lights plugged into my 4 pin on the MB and worked. I didnt test the included remote nor did I play around with the lighting. I was mostly concerned about the heat situation, which this thing rocked. There is an insane amount of wire length for the Lighting connections.
Overall, this thing is great, does a great job of cooling and is quiet.
Images in this review
Reviewed in the United States on July 24, 2023
Color: BlackSize: 420mmStyle: ARGBPattern: CoolerVerified Purchase
Reviewed in the United States on July 7, 2023
Color: BlackSize: 420mmStyle: ARGBPattern: CoolerVerified Purchase
Reviewed in the United States on March 7, 2023
Color: WhiteSize: 360mmStyle: ARGBPattern: CoolerVerified Purchase
Reviewed in the United States on July 26, 2023
Color: BlackSize: 120mmStyle: ARGBPattern: CoolerVerified Purchase
Reviewed in the United States on July 26, 2023
Color: BlackSize: 420mmStyle: ARGBPattern: CoolerVerified Purchase
Top reviews from other countries
Big E
Worked perfectly with my Aurora R12
Reviewed in Canada on May 29, 2023Color: WhiteSize: 120mmStyle: ARGBPattern: CoolerVerified Purchase
GEORGINA GARCIA G.
Excelente
Reviewed in Mexico on April 25, 2023Color: BlackSize: 360mmStyle: ARGBPattern: CoolerVerified Purchase
GEORGINA GARCIA G.
Reviewed in Mexico on April 25, 2023
Images in this review
Pedro Ernesto Manuel Gonzalez Jimenez
facil
Reviewed in Mexico on February 22, 2023Color: WhiteSize: 120mmStyle: ARGBPattern: CoolerVerified Purchase
rajurajeev24
Best Cooler For the Price
Reviewed in Canada on September 5, 2022Color: BlackSize: 360mmStyle: ARGBPattern: CoolerVerified Purchase
rajurajeev24
Reviewed in Canada on September 5, 2022
Very strong at its job of cooling keeping the processor nice and cool even through rigorous benchmarks (with 12700K). Very quiet even at full operation which is a nice bonus at this price. The pump also works without any sound.
Installation is not possible from the top due to the hose's length and its connection point onto the cooling brick. It's not very flexible but is workable from a side mount (as recommended in the product and box images). The colour accuracy of the RGB fans are not great (see picture) making them look kind of cheap despite their good quality. RGB cooling brick is very good (and colour accurate) and comes with LGA 1700 as promised.
Installing and cable managing the fans is a little tricky and although the accompanying instructions are not great, their youtube video is sufficient.
Will update if anything goes wrong
Installing the
Images in this review
BAGEL
One month in and still good
Reviewed in Canada on June 10, 2022Color: BlackSize: 120mmStyle: ARGBPattern: CoolerVerified Purchase
