Customer Questions & Answers

Find answers in product info, Q&As, reviews

There was a problem completing your request. Please try your search again later.
All Product Information Customer Q&A's Customer Reviews

Your question may be answered by sellers, manufacturers, or customers who purchased this item, who are all part of the Amazon community.

Please make sure that you are posting in the form of a question.

Please enter a question.

Showing 1-10 of 197 questions
Sort by
  • 5
    vote

    votes
Answer:
It works fine as a dual bay enclosure. I've swapped lots of drives and have never used the clone feature.
stuffgeeekswant-dot-com
· April 4, 2017
  • 2
    vote

    votes
Answer:
Thanks for your question, we are gald to help you.
Hard Drive Duplicator Function
HDD A----Source HDD HDD B----Target HDD… see more
Thanks for your question, we are gald to help you.
Hard Drive Duplicator Function
HDD A----Source HDD HDD B----Target HDD
1.Make sure there are no connection on the USB.
2.Ensure the Power Switch on the rear is in the OFF Position and plugged in properly.
2. Insert the HDD A in the rear near the power plug and insert the HDD B in the front.
3.Offline clone is from HDD A to HDD B. Make sure your Main Drive is in HDD A and slave in HDD
B. The capacity of HDD B must be equal or bigger than HDD A.
4. Press and hold the offline clone button for 3 seconds, the LED indicator will light up. Then
quickly press the offline clone button and the offline clone operation will start. Each LED
represents 25% completion. It is only when every 25% of HDD A is offline clone to HDD B that
such LED will remain constantly on. When offline clone operation is fully completed, all LEDs will
constant on until the device is power off.
Unable to clone:
Please check if the capacity of Disk B is larger or equivalent to that of Disk A.
Here the capacity means the actual capacity that can be used, instead of the one marked on the
product. For example, the actual capacity of a disk marked 500GB might be 480GB only. The
actual capacity of disks with the same marked capacity differs if they are produced by different
producers. To ensure two disks of the same marked capacity have the same actual capacity, they
should be produced by the same producer in the same batch with the same model number.
b. Indicator light stops flashing up during offline duplicating: it might because of disk bad sectors
so that data couldn’t be cloned as usual. It’s better to change a good disk.
c. After cloning, the rest capacity of B disk is showed and operated via ”Computer management -
Storage - Disk management”.
d. Why over 2TB hard disk couldn’t be identified by USB? Because the maximum capacity of hard
disk which Windows XP can supports is 2TB and couldn’t be identified by system if over 2TB. It
only supports after upgrading the operating system above Vista (64 bit) version and we suggest
changing hard disk into a GPT disk partition, or the operating system will not support over 2 TB
disk partitions.
e. Please make sure that B hard disk data can be covered before cloning data. Because once you
start cloning, B hard disk partition methods and data are completely cloned as A hard disk. Our
company does NOT undertake any responsibility for data or economy loss which could bring by
damaged data.
f. Please do not remove your hard drive or insert a new one while the other hard drive is being
accessed, as doing so the other drive temporarily disconnects and this could damage your hard
drive and result in data loss.
Hope the above information helps! If you need any additional information, please do feel free to shoot us an email at Daisy@wavlink.com. We are here to help!
Thanks!
Regards,
Daisy see less
Thanks for your question, we are gald to help you.
Hard Drive Duplicator Function
HDD A----Source HDD HDD B----Target HDD
1.Make sure there are no connection on the USB.
2.Ensure the Power Switch on the rear is in the OFF Position and plugged in properly.
2. Insert the HDD A in the rear near the power plug and insert the HDD B in the front.
3.Offline clone is from HDD A to HDD B. Make sure your Main Drive is in HDD A and slave in HDD
B. The capacity of HDD B must be equal or bigger than HDD A.
4. Press and hold the offline clone button for 3 seconds, the LED indicator will light up. Then
quickly press the offline clone button and the offline clone operation will start. Each LED
represents 25% completion. It is only when every 25% of HDD A is offline clone to HDD B that
such LED will remain constantly on. When offline clone operation is fully completed, all LEDs will
constant on until the device is power off.
Unable to clone:
Please check if the capacity of Disk B is larger or equivalent to that of Disk A.
Here the capacity means the actual capacity that can be used, instead of the one marked on the
product. For example, the actual capacity of a disk marked 500GB might be 480GB only. The
actual capacity of disks with the same marked capacity differs if they are produced by different
producers. To ensure two disks of the same marked capacity have the same actual capacity, they
should be produced by the same producer in the same batch with the same model number.
b. Indicator light stops flashing up during offline duplicating: it might because of disk bad sectors
so that data couldn’t be cloned as usual. It’s better to change a good disk.
c. After cloning, the rest capacity of B disk is showed and operated via ”Computer management -
Storage - Disk management”.
d. Why over 2TB hard disk couldn’t be identified by USB? Because the maximum capacity of hard
disk which Windows XP can supports is 2TB and couldn’t be identified by system if over 2TB. It
only supports after upgrading the operating system above Vista (64 bit) version and we suggest
changing hard disk into a GPT disk partition, or the operating system will not support over 2 TB
disk partitions.
e. Please make sure that B hard disk data can be covered before cloning data. Because once you
start cloning, B hard disk partition methods and data are completely cloned as A hard disk. Our
company does NOT undertake any responsibility for data or economy loss which could bring by
damaged data.
f. Please do not remove your hard drive or insert a new one while the other hard drive is being
accessed, as doing so the other drive temporarily disconnects and this could damage your hard
drive and result in data loss.
Hope the above information helps! If you need any additional information, please do feel free to shoot us an email at Daisy@wavlink.com. We are here to help!
Thanks!
Regards,
Daisy

WAVLINK Direct
Seller · August 16, 2017
  • 1
    vote

    votes
Answer:
Yes
Theaoneone
· February 24, 2017
  • 1
    vote

    votes
Answer:
Yes it works with Xboxes.
Jim Crook
· March 10, 2019
  • 1
    vote

    votes
Answer:
With the proper cloning software, yes it will. I did the same thing.
Richard K. Cooney Jr.
· March 18, 2019
  • 1
    vote

    votes
Answer:
Yes, it work with Windows 10
WAVLINK Direct
Seller · August 9, 2018
  • 1
    vote

    votes
Answer:
The socket is for a USB 3.0 B cable and the included cable is similar to this
https://www.amazon.com/AmazonBasics-USB-3-0-Cable-Male/dp/B00NH144GK

Dane . .
· December 30, 2017
  • 0
    vote

    votes
Answer:
No. It is USB 3.1 only - no other interface.
Gary Goodnow
· February 19, 2019
  • 0
    vote

    votes
Answer:
Wavelink supports 2x 8TB hard drive; Supports 2.5" & 3.5" SATA (SATA I/ II/ III) HDD and SSD. I suggest Wavelink bundle with new USB 3.1 cable
Wavelink working with WD Green 1 (old drive) /2/6 TB Desktop Hard Drive: 3.5 Inch. I have not tried it with 2.5 TB Green HD. It should work, if not you can always return.

Charles Tran
· August 28, 2017
  • 0
    vote

    votes
Answer:
Yes I boot another OS from this
John N
· March 19, 2019