Okay, there are a number of reviews here on Amazon that point out the cons of this unit. Allow me to say this about how the regulators are installed on the heatsink. The only way to keep costs down as well as build assembly simple, is to use this method. Other options would require active cooling with a noisy fan and internal heatsinks with pin guides for the PCB which for people new to kits like this (and Elenco designs this series for students), would increase difficulty. If you've never loosely stuck a TO pack to a pin guided heatsink (with thermal grease), then tried to tighten things up and solder in place, then finish screwing it in place before ( and that would have to be done four times in this kit), then this is a much simpler solution. All things considered I would prefer to have the individual heatsinks on the PCB, but I do get the design for cost and build simplicity. But as others have said make sure you heat shrink the exposed leads of each of the TO packs, so make sure to have some on hand.
Now for the binding posts, there is no excuse. Elenco not only picked the cheapest posts they could find, when it became a problem they didn't bother to correctly address the problem. See a modern, quality binding post will be hard nickel plated on the post part but the area you attach the wiring will either be gold plated or bare, polished copper. Why? Because you can solder to gold or copper. You cant really solder to nickel very well. The reason they are fully nickel plated is because of costs. Nickel is a good electrical conductor (not great, but good enough), and really resists wear from the constant friction of plugging and unplugging of your leads. So thats a good thing. But when these cheap posts are made, they just plate the entire steel part in nickel instead of just the binding part and then polishing the internal hookup part as that is several extra steps that raise costs. So Elenco decided that on the 2010 revision of this kit to include 7 extra nuts but not add instruct the builder that they should just use the extra nuts to attach the wires in place with. Now the overall quality of the posts is fine, you just cant really solder the wires to them easily. Trying to use the extra nuts to bind them to the posts in cramped quarters is also pretty annoying. Run down to your local Radio Shack and pick up a $2.00 pack of 22 gauge ring terminals (catalog 64-3114) and use them instead. Just give yourself and extra half inch of wire on each of the binding post wires. Strip off one full inch instead of the 1/4" the instructions say. Double it over and solder it together. Then crimp it in the ring terminal and screw into place with the extra nut. Much simpler than trying to solder the posts or holding the wire in place in such cramped quarters.
Other than that, the only parts I found that were just bad were a couple of caps. One of the 22,000µf and my 47,000µf were right at the very brink of their +/- 20% range, so I upgraded all my caps to new, high temp, low ESR caps that should last a good decade or two. Total price was an extra $7.00 with shipping. So if you can, check your caps before you build. You should be fine, but caps are cheap and good ones will last for a long time.
A few do's and don'ts for the kit: Dont use the included lead free solder unless you have a tip and iron for lead free solder. Its hard to work with, it eats up your tip, and requires a good bit of excess heat. Do get some .20, .30, or .40 size 60/40 or 63/37 lead solder with a rosin core. When it comes to electronics, lead is indeed your friend. Don't use the included two pieces of plastic based heatshrink tubbing. Do get an assortment pack of different size heatshrink tubbing and use that instead. Heatshink all exposed contact points in the kit with individual tubes and not just one big one.
This kit can be modded a bit. Like many who have built this kit, I chose to install a couple of 2k, 10 turn, wire wound pots to make fine tuning type adjustments. The simple carbon pots that come with the kit will work just fine. I just wanted more precision (ie fine tuning) when setting my voltages. If you don't happen to have a couple of these in your parts bin, then they will cost a bit. Upwards of $35.00 for two with shipping. That includes an extra few bucks for new dials since the included dials, wont fit most multi-turn pots. If you go this route, you will have to drill out the holes just ever so slightly more. We're talking just a hair or two.
There is also plenty of room for a display to be installed in the company logo area of the front panel. I will be adding one in the future as I can see that checking my voltage every time with a multimeter will become a bit of a pain. I've already seen one kit where somebody installed a 20 x 4 line LCD display for this and it reads voltage and amps for all outputs.
There is even a little extra room between the AC and DC rails for installing a load circuit, which I plan to do.
So you can spend twice the price to upgrade this kit if your not careful. Keep in mind that most of these mods are just fun to add and helpful but are not needed. For that amount of cash you could just but a PSU with a display, and fine tuning built in. But the main reason to do it with this kit is it offers dual adjustable DC jacks at 1 amp, a constant 5v DC at 3 amps, and a 6.3/12.6v AC. You cant come anywhere near a quality tri-rail PSU at the $120-$130 mark. So the mods can be fun, useful, let you learn a little if your new to electronics and offer serious bang for the buck features that you would normally pay several hundred bucks for in a prebuilt PSU.
The case and transformer are very well made and should last a very long time if treated with care. The taps on the transformer are made with silicone covered wire (which really surprised me) so they wont get brittle with age and heat like the common PVC types. The overall circuit is very simple, through hole based so if a componet happens to fail it would be an easy fix.
All in all, its a great value kit that offers lots of upgrades options and should last a long time. I got it in January when Amazon was selling it for $49.00 (with prime), and I see that its now up to $59.00. That seems to be the average price online, so I dont think it will really go up more than this. I've put about $40.00 in parts and upgrades to it, and I'm very pleased with the end result. When I'm finished with future upgrades it will be about $120-$130 spent and I'll have a very versatile PSU, thats cool running, silent, and built to last. I give it five stars.
***EDIT***
Quick tip for building: Flux and tin ALL the PCB solder pads before you begin to populate the board. The solder pads on the PCB are beyond huge and if you try to solder components without the tinning, it will make the work much slower as it will take forever to heat up those large areas and leave your iron on your parts for to long. Don't forget to clean off any excess flux when you are done assembling the PCB.
Consider a similar item
Frequently bought together
This item: Elenco AC/DC Triple Output Power Supply Kit
$89.10
In Stock
+
$9.99
In Stock
+
Total price: $00
To see our price, add these items to your cart.
Choose items to buy together.
From the brand
From the manufacturer
|
|
|
|
|
|
|---|---|---|---|---|---|
| Elenco FM Radio Kit | Elenco Practical Soldering Kit | Snap Circuits SC-100 | Smartivity Music Machine | Teach Tech Zivko Robot | |
| Customer Reviews |
1,469
|
547
|
27,216
|
693
|
1,043
|
| Price | $17.99 | $12.93 | $29.99 | $38.27 | $35.99 |
| STEM Education | ✓ | ✓ | ✓ | ✓ | ✓ |
| Minimum Age | 13+ | 12+ | 8+ | 8+ | 10+ |
| Practical Skills | ✓ | ✓ | ✓ | ✓ | ✓ |
| Batteries Required | None | None | None | ✓ | ✓ |
Products related to this item
Page 1 of 1Start overPage 1 of 1
A very nice kit
Based on previous reviews, I added R6, R7, R8 discharge resistors (to quickly discharge big caps after power-off), D9-D13 protection diodes (to prevent inductive loads from damaging voltage regulators) and C10-C11 bypass capacitors (to suppress HF noise). See the attached schematics. I employed crimp terminals (22-18AWG #8) instead of soldering wires as can be seen in the pic (a tip from a previous reviewer). I also added DROK digital meters (combined voltmeter/ammeter):DROK 0.28"High Accuracy DC 0-33.00V/0-999.9mA-3.000A 12V Voltmeter Ammeter Voltage Current Tester Monitor Panel Gauge.Edit on 6/1/2017:I ordered and installed multi turn 2K potentiometers, $6.72 for two pots including 11 day delivery from China:CNBTR Wirewound Cylindrical Potentiometers 2K Ohm 10 Turn 3590S-2-202L Rotary Shaft Set of 2.It made a huge difference: as you can see on the new picture, it's possible now to control voltage with up to 10 mV precision.I had to use a 1/4" drill bit to adjust the original knobs for the mult-turns' 1/4" shaft.
Top reviews from other countries
S. Affleck
Fantastic kit for those who want to learn about how power supplies work.
Reviewed in Canada on July 25, 2020
